Aube TH232-AF-230 Manual

Aube Termostat TH232-AF-230

Læs gratis den danske manual til Aube TH232-AF-230 (4 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Aube TH232-AF-230, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

TH232-AF-230 400-232-003-B 2010-05-26 1/4

• One (1) thermostat

• One (1) floor sensor

• One (1) wall plate

Turn off power to the heating system at the main power panel to

avoid electrical shock. Installation should be carried out by an

electrician.

 All work must conform to the applicable country standards for

electrical installations and wiring.

 This thermostat should be connected on a circuit equipped with

a fuse or a circuit breaker. It must be installed on a certified

electrical box equipped with non-metallic cable strain relief

adapters. Use separate adapters for the high-voltage wires and

for the sensor cable.

 For a new installation, choose a location about 1.5 m above the

floor.

 For electric baseboards, convectors and fan-forced heaters, the

thermostat must be installed facing the heating system and on

an inside wall.

 Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or

concealed chimneys or stove pipes.

NOTE: The terminals are designed to handle a cross-section of wire

measuring 0.33 to 3.1 mm2.

Loosen the captive screw underneath the base and remove the

faceplate from the base.

Before making the connections, make sure

that the base covers the electrical box

entirely. If not, install a wall plate at the

back of the base.

Connect the wires:

• :Power

Terminals 1 & 5

•Load:

Terminals 2 & 4

see note 1

•Pilot Wire:

Terminal 3

see note 2

• :Floor sensor

Terminals 6 & 7

(no polarity)

see note 3

WARNING: Ensure that the wires are tightly secured to the terminals.

Apply a minimum torque of 0.5 Nm (4.4 Lb/in) when tightening the

screws.

Note 1 If a contactor is used between the thermostat and the load,

install a snubber at the contactor’s coil terminal to ensure

the proper operation of the thermostat.

Note 2 This connection is required on some models only.

Note 3 The sensor cable must pass outside the electrical box and

travel inside the wall to the floor. For the proper operation of

the thermostat, the floor sensor must be centered between

two heater wires having a maximum temperature of 80 °C

(176 °F). The floor sensor wire must not cross any heater

wire or be placed close to it.

Push wires into the electrical box and

secure the base to the electrical box

anchorage. The head of the screw

must be less than 2 mm thick.

Return the faceplate

to the base.

 Return power to the heating system.

NOTE: Keep the thermostat's air vents clean and unobstructed at all

times.



 1.



 2.



 3.

Base

Faceplate

TH232-AF-230 400-232-003-B 2010-05-26 2/4

This thermostat provides the following temperature control modes:

Display

Apply power to the thermostat at the main electrical panel. At

power-up, the thermostat is in manual mode and displays the

actual (measured) temperature. The setpoint temperature is 28 °C

(82 °F).

LO The actual temperature is below 0 °C (32 °F).

HI The actual temperature is above 70 °C (158 °F).

Er The thermostat built-in sensor is defective. Replace the

thermostat.

E1 The floor sensor circuit is opened. Check the sensor

connections.

E2 The floor sensor circuit is shorted. Replace the sensor.

Press and hold the Clear button for 3 seconds. The current con-

trol mode is displayed ( )ctl .

Press the to select between A, AF and F.

NOTE

: If you have chosen the A or F mode, go to step 7. If you have

chosen the AF mode, the thermostat will control the ambient tempera-

ture while keeping the floor temperature within desired limits. If the

floor temperature is too low or too high, the thermostat will turn heating

on or off to maintain the floor temperature within the limits regardless

of the ambient temperature. The minimum and maximum floor temper-

ature limits are factory-set at 5 °C (41 °F) and 28 °C (82 °F) respec-

tively. To modify the limits, continue with the next step:



Press the

Clear

button briefly. The minimum limit is displayed (

FL:LO

Press the button to set the minimum limit.



Press the

Clear

button briefly. The maximum limit is displayed (

FL:HI

Press the buttons to set the maximum limit.

Press the Mode/Return button to exit and save the changes.

NOTE: If no button is pressed for 60 seconds, the thermostat will

save the changes and return to normal display.

This procedure allows you to choose the following configurations:

Press and hold the Pgm button for 3 seconds. The current tem-

perature unit is displayed (unit).

Press the to toggle between °C and °F.

Press the Pgm button briefly. The current time format is dis-

played (Hr).

Press the to toggle between 24H and 12H.

Press the Pgm button briefly. The current Early Start setting is

displayed (ES).

Press the to toggle between OFF and On.

Press the Mode/Return button to exit and save the changes.



 1.

A mode:  controls and displays the ambient air temperature

F mode:  controls and displays the floor temperature using

an external temperature sensor (default mode)

AF mode:  controls and displays the ambient air temperature

 maintains the floor temperature within desired

limits using an external temperature sensor



 2.



 3.

Day and

time setting

Schedule

programming

Mode selection /

Exit

Clear

Temperature

adjustment

Temperature

presets

On/Off button *

* Use this button to disable heating (e.g. in the summer). The

thermostat remains powered and continues to display the time

and temperature.

Time

Day

Temperature

Periods

Heating intensity

indicator

Automatic mode

Appears when the

setpoint temperature

is displayed

Appears when

heating is disabled

Mode indicator (A, F or AF)

Preset temperature

indicators

Manual mode



 4.

Parameters Default settings

Temperature format °C

Time format 24H

Early Start setting (see the note below) On

Produkt Specifikationer

Mærke:	Aube
Kategori:	Termostat
Model:	TH232-AF-230

Har du brug for hjælp?

Hvis du har brug for hjælp til Aube TH232-AF-230 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Aube Manualer

Aube TH115 AF Manual

26 Juli 2024

Aube TH232-AF-230 Manual

3 August 2023

Aube TH106 Manual

24 Oktober 2022

Aube TH132 F Manual

18 Oktober 2022

Termostat Manualer

Nyeste Termostat Manualer

Bticino NT4451 Manual

8 Oktober 2025

Bticino HS4451 Manual

7 Oktober 2025

Bticino N4451 Manual

7 Oktober 2025

Bticino L4451 Manual

7 Oktober 2025

Bticino AM5721 Manual

6 Oktober 2025

Bticino L4441FH Manual

6 Oktober 2025

Bticino Living 4477 Manual

6 Oktober 2025

Bticino HC4451 Manual

6 Oktober 2025

Emerson ST75 Manual

1 Oktober 2025

Homematic IP HMIP-eTRV Manual

30 September 2025