Aurel TXSAW433 Manual

Aurel Modtager TXSAW433

Læs gratis den danske manual til Aurel TXSAW433 (5 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Aurel TXSAW433, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/5
TX- -SAW/433 s Z
Instruction Manual
Technical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.
AUR°EL S.p.A. Via Foro dei Tigli, 4 - - - 47015 Modigliana (FC) – ITALY Rev. A, 19 09 2001
Tel.: +390546941124 – 1 Fax: +390546941660 Pag of 5
http://www.aurel.it - email: aurel@aurel.it
TX- -SAW / 433 s Z Transmitter
SAW Transmitter module with external antenna, for utilisations with ON-OFF modulation of a RF carrier with digital data.
Pin-out
Connections
Pin 1- -4 13 Ground GND Connections. To be externally connected to a single ground plate.
(see fig. 3)
Pin 2 Input Mod. TTL 0÷5V type data input with a minimum 5KΩ resistance. Connection
utilized only if the supply to pin 15 is +12V ±10% (see fig. 2)
Pin 3 Input Mod. TTL 0÷5V type data input with a minimum 5KΩ resistance. Connection
utilized only if the supply to pin 15 is +5V ±10% (see fig. 2)
Pin 11 RF output RF output with a characteristic impedence of 50Ω
Pin 15 +V Connection to the positive pole of the +5V ±10% supply
Max voltage values allowed
Description Max Unity Remarks
Voltage supply (Vs) to pin 15 13,5 V
Technical features [ETS 300 200]
Description Min Typical Max Unity Remarks
Working frequency centre 433.82 434.02 433.92 MHz See notes 1 and 2
Voltage supply (Vs) 4.5 5.5 5 V
Absorbed current 4 mA
RF output power (E.R.P.) +10 dBm See note 1
Output impedance pin 11 50 Ω
RF spurious emissions -50 dBm See note 1
Modulation frequency 4 kHz
Input high logic level 4.5 5.5 5 V
Input low logic level 0 0.2 V
Working temperature -20 +80 °C See fig. 5
Working temperature [ETS 300 200] -20 +55 °C See fig. 5
Dimensions 38.1 x 13.2 x 3 mm See Pin-out
Note1: Values have been obtained by applying the test system shown in Fig. 1 and maximum 5,5 V power supply.
Note2: The minimum and maximum showed values are determined by the device’s construction tolerance.
To define the working frequency of the device, add to these values the deviation caused by the thermal variations (see fig. 3).
Note3: To keep the parameters within the limits established by the rules in force, (see para. “Reference Rules”), it is recommended to
supply the circuit with not more than 5,5V and to comply with all the recommendations specified in para “Device usage”.
Messrs AUR°EL declines all responsibilities in case the a.m. recommendations are disregarded.
Lot (Week/Year) Code
1
15
TX- -SAW/433 s Z
Instruction Manual
Technical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.
AUR°EL S.p.A. Via Foro dei Tigli, 4 - - 47015 Modigliana (FC) – ITALY Rev. A, 19 09-2001
Tel.: +390546941124 – 2 Fax: +390546941660 Pag di 5
http://www.aurel.it - email: aurel@aurel.it
The declared technical features have been obtained by applying the following testing system:
Device usage
In order to obtain the performances described in the technical specifications and to comply with the
operating conditions, which characterize the Certification, the transmitter has to be mounted on a printed
circuit, and keep into consideration what follows:
5V dc supply
1. The transmitter must be supplied by a very low voltage source, safely protected against short circuits.
2. Maximum voltage variations allowed: ± 0,5 V.
3. De-coupling, next to the transmitter, by means of a minimum 100.000 pF ceramic capacitor.
Ground
1. It must surround at the best the welding area of the transmitter. The circuit must be double layer, with
throughout vias to the ground planes, approximately each 15 mm.
2. It must be properly dimensioned, especially in the antenna connection area, in case a radiating whip
antenna is fitted in it (an area of approximately 50 mm radius is suggested).
TX- -SAW/433 s Z
+5V DC
Power
Supplier
Spectrum
analyzer
Square wave generator :
4 KHz frequency
Out Level 0
÷÷
5V RF 50
ΩΩ
Input
Pin 3
Pin 11
50 Ù
coaxial
cable
connection

Produkt Specifikationer

Mærke: Aurel
Kategori: Modtager
Model: TXSAW433

Har du brug for hjælp?

Hvis du har brug for hjælp til Aurel TXSAW433 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Aurel Manualer

Aurel

Aurel MCAUHF479 Manual

17 August 2024
Aurel

Aurel TXSAW433 Manual

16 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Audiotec Fischer

Audiotec Fischer V Twelve DSP MK2 Manual

10 Oktober 2025
TOA

TOA DA-1250D Manual

10 Oktober 2025
JVC

JVC KW-Z800AW Manual

10 Oktober 2025
TOA

TOA P-2240 SA Manual

10 Oktober 2025
TOA

TOA P-2240 H Manual

10 Oktober 2025
Caliber

Caliber CA100.2M Manual

8 Oktober 2025
Crown

Crown CDi DriveCore 4|1200 Manual

8 Oktober 2025
Caliber

Caliber CA3000P1 Manual

8 Oktober 2025
IFi Audio

IFi Audio GObar Manual

8 Oktober 2025
Ocean Matrix

Ocean Matrix OMX-04SISI0001 Manual

8 Oktober 2025