AXESS AX-BXLOC2-PRO Manual
AXESS
Ikke kategoriseret
AX-BXLOC2-PRO
Læs nedenfor 📖 manual på dansk for AXESS AX-BXLOC2-PRO (8 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 24 personer og blev bedømt med 4.5 stjerner i gennemsnit af 12.5 brugere
Side 1/8
AX-BXLOC2-PRO
I N S TA L L A T I O N I N S T R U C T I O N S
MetraOnline.com © COPYRIGHT 2023 METRA ELECTRONICS CORPORATION REV. 8/18/23 INSTAX-BXLOC2-PRO
TABLE OF CONTENTS
Quick Start Guide
Things to Know 2 .................................................
Connections .......................................................2
Gain setup
Basic setup 3 .........................................................
Advanced Setup 3 ................................................
Setting up Bass-X 4 ..................................................
Feature Breakdowns 5 .............................................
Quick Reference 6 .....................................................
Diagram 7 ..................................................................
Specifications 8 .........................................................
Premium Active LOC with Bass Restoration 2 IN - 4 OUT, Input Of 400 Watts Per Channel, 40v Max
TOOLS RECOMMENDED
• Digital Multi-meter
• Test Tones
Universal Premium LOC
The Axxess AX-BXLOC2-PRO is a compact premium line output converter with active input circuitry, which allows it to accept speaker-level signals
of up to 400 watts per channel from factory-installed source units or amplifiers. It converts them to high-quality pre-amp signals that can then
be directed to aftermarket amplifiers. The offers for those factory radios or amplifiers that stop passing AX-BXLOC2-PRO Built In Load Resistors
audio when OE speakers are disconnected. The built in load resistors trick the factory equipment to pass audio into the Axxess LOC allowing easy
audio upgrades. Many of these factory audio systems regulate lower frequencies to prevent potential damage to the OE speakers, which is not a
desirable feature when wanting to add subwoofers to your OE system. Some OE radios and amplifiers can reduce the output of low frequencies
as the volume is increased. Having a product with a Bass-X restoration circuit in the LOC will allow users to enjoy their music as it was recorded.
Users can enjoy maximum sound quality while maintaining the use of factory volume and steering wheel controls. A bass remote control with
digital voltmeter is included, so that you can monitor your car audio amplifier voltage to prevent damage to all your car audio equipment.
Bass Knob AX-BXLOC2-PRO Line Out Converter (LOC)
COMPONENTS
2
THINGS TO KNOW
1. This is an active LOC and MUST have constant 12 volt and a good ground to operate properly.
Having a poor ground can induce noise into your system, use the same gauge wire as the
12 volt line.
2. Determine a suitable mounting location. Make sure you can access all controls and
connections.
3. When ready to mount your LOC, check under your selected mounting location to make sure
it is clear of any wiring harnesses, fuel or brake lines, or anything else that may affect the
vehicle safety.
QUICK START GUIDE
CONNECTIONS
1. Connect your 12 volt and ground wires to the terminals. 14-16 gauge wire is recommended.
2. Turn On Mode DC Offset By default the LOCs is set to . Other turn on options are available
and described in the portion of this manual.Turn On Signal Feature Breakdown
3. Speaker Input Connecting your can happen in a few different places based on your factory
system.
If your vehicle doesn’t have an OE amplifier your best option is to use the speaker wires a.
located behind the radio. Your LOC only requires two inputs, we recommend a left
and right signal full range signal.
If your vehicle has an OE amplifier your best option is to use the speaker wires on b.
the output side of your factory amplifier, look for a full range signal.
4. Find a suitable mounting location of the and run the control wire to that location Bass Knob
in the vehicle. The included offers a voltage display and control ofBass Knob Bass Output
levels.
5. Red Black, Gray, White Connect your RCAs. RCAs are for the right channel. or are for the left
channels. An explanation of the RCA’s and are described in the Main Output Bass Output
Feature Breakdown portion of this manual.
Produkt Specifikationer
| Mærke: | AXESS |
| Kategori: | Ikke kategoriseret |
| Model: | AX-BXLOC2-PRO |
Har du brug for hjælp?
Hvis du har brug for hjælp til AXESS AX-BXLOC2-PRO stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret AXESS Manualer
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
25 Februar 2025
27 Januar 2025
Ikke kategoriseret Manualer
- Ikke kategoriseret Technicolor
- Ikke kategoriseret Globe
- Ikke kategoriseret Lewitt
- Ikke kategoriseret Maxdata
- Ikke kategoriseret Regula-Werk King
- Ikke kategoriseret Vitamix
- Ikke kategoriseret Chauvet
- Ikke kategoriseret Better Life
- Ikke kategoriseret Catler
- Ikke kategoriseret Moomin
- Ikke kategoriseret Sensiplast
- Ikke kategoriseret Izzy
- Ikke kategoriseret Kopul
- Ikke kategoriseret Python
- Ikke kategoriseret DataComm
Nyeste Ikke kategoriseret Manualer
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025