AXESS AX-FT902 Manual

AXESS Ikke kategoriseret AX-FT902

Læs gratis den danske manual til AXESS AX-FT902 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om AXESS AX-FT902, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-FT902

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.) • Zip ties

TABLE OF CONTENTS

Connections to be made ....................................2-3

Installing the AX-FT902 interface .........................3

Programming the ASWC-1 interface ................. 3-4

Screen operation ................................................4-6

Fiat 500X (with U-Connect) Data Interface with SWC & Factory Display Retention 2015

• Provides accessory power

• Designed for non-ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains parking sensor chimes

• Retains balance and fade

• Retains most of the vehicle settings that was displayed on the

factory radio *

• Micro “B” USB updatable

• AX-FT902 interface

• ASWC-1 interface

• AX-FT902 harness

• ASWC-1 harness

• Female 3.5mm connector with stripped leads

• Chime Speaker

* Attention!

The aftermarket radios backup camera input will be used to display the vehicle settings. If the radio doesn’t have a backup camera

Input, then there will be no visualization of the vehicle settings. An externally mounted screen could be substituted in this situation.

CONNECTIONS TO BE MADE

From the aftermarket radio to the AX-FT902 harness:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the accessory wire.Red

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the wire to the power antenna turn-on wire.Blue

• Connect the wire to the left front positive speaker wire.White

• Connect the wire to the left front negative speaker wire.White/Black

• Connect the wire to the right front positive speaker wire.Gray

• Connect the Gray/Black wire to the right front negative speaker wire.

• Connect the wire to the left rear positive speaker wire.Green

• Connect the wire to the left rear negative speaker wire.Green/Black

• Connect the wire to the right rear positive speaker wire.Purple

• Connect the wire to the right rear negative speaker wire.Purple/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wire.Light Green

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls or a backup camera.

• Connect the wire to the accessory wire.Red

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to

the

male 3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard

• Connect the steering wheel control wire, normally Eclipse: Brown Brown/, to the

White wire of the connector. Then connect the remaining steering wheel control wire,

normally , to the wire of the connector.Brown/White Brown

• Connect the steering wheel control Key 1 wire (Gray) to the wire.Metra OE: Brown

• Kenwood or select JVC with a steering wheel control wire: Blue/Yellow Connect the

wire to the wire.Brown

• XITE:

Connect the steering wheel control SWC-2 wire from the radio to the Brown wire

•

Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as

Key-A or SWC-1, to the

Brown

wire of the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the

Brown/White

wire of

the connector. If the radio comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio manufacturer

for more information.

Continued on the next page

Produkt Specifikationer

Mærke:	AXESS
Kategori:	Ikke kategoriseret
Model:	AX-FT902

Har du brug for hjælp?

Hvis du har brug for hjælp til AXESS AX-FT902 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret AXESS Manualer

AXESS AXABH-FD1 Manual

30 Juli 2025

AXESS AXABH-TY3 Manual

30 Juli 2025

AXESS AXBUCH-MZ6V Manual

29 Juli 2025

AXESS AXABH-CH3 Manual

29 Juli 2025

AXESS AXDSPX-HK5 Manual

25 Februar 2025

AXESS AXAMP-CH8 Manual

25 Februar 2025

AXESS AXTC-MZ1 Manual

25 Februar 2025

AXESS AXBUCH-TYCAM26V Manual

25 Februar 2025

AXESS AXAMP-FD2 Manual

25 Februar 2025

AXESS AXBUCH-TYCAM36V Manual

25 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite Protect It! TLP606 Manual

30 Juli 2025

AMX NMX-WP-N2510 Manual

30 Juli 2025

Yealink SIP-T23G Manual

30 Juli 2025

Rothenberger ROBEND 4000 Manual

30 Juli 2025

Tripp Lite SUPDMB710 Manual

30 Juli 2025

Tripp Lite IBAR6ULTRAUSBB Manual

30 Juli 2025

Advantech PCM-34R1TP Manual

30 Juli 2025

Tripp Lite SRIN4141410 Manual

30 Juli 2025

Tripp Lite TLM609GF Manual

30 Juli 2025

Tripp Lite Protect It! TLP368CUBEUAM Manual

30 Juli 2025