AXESS AXHN-1 Manual

AXESS Ikke kategoriseret AXHN-1

Læs gratis den danske manual til AXESS AXHN-1 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om AXESS AXHN-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AXHN-1

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun,

solder, and heat shrink • Small ﬂat-blade

screwdriver • Tape • Wire cutter • Zip ties

TABLE OF CONTENTS

Connections to be made ....................................... 2

Installing the AXHN-1 ............................................. 3

Programming the AXHN-1 .....................................3

Setting the factory clock ....................................... 3

Troubleshooting .....................................................3

Honda Clock Retention 2012-2014

APPLICATIONS

• Provides accessory power (12-volt 10-amp)

• Can be used in non-ampliﬁed, or ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• AXSWC harness included (AXSWC sold separately)

• Retains balance and fade

• Retains the ability to set the factory clock

• Retains the factory AUX-IN jack

• Micro-B USB updatable

• AXHN-1 interface • AXHN-1 harness

• 8-pin subwoofer harness

• 16-pin harness with stripped leads

HONDA

Civic * (without NAV) 2013 CR-V (without NAV) 2012-2014

* All trims except LX

CONNECTIONS TO BE MADE

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the wire to the accessory wire.Red

• Connect the Orange/White wire to the illumination wire. If the aftermarket radio does not

have an illumination wire, tape it off and disregard it.

• Tape off and disregard the , Gray Gray/Black White White/Black Brown, , , and wires, they

will not be used in this application.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the parking brake wire (if applicable).Light Green

• Connect the wire to the VSS or speed sense wire (if applicable).Blue/Pink

• Connect the wire to the reverse wire (if applicable).Green/Purple

From the AXHN-1 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• If the vehicle is equipped with a factory ampliﬁer, connect the Blue/White wire to amp

turn-on wire.

• If the vehicle is equipped with a factory AUX-IN jack and desired to be retained, connect the

Red & RCA jacks to the AUX-IN jack.White

For the following (8) wires, if the vehicle does not have a factory ampliﬁer, cut off the RCA jacks

to expose the speaker wires.

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

• Connect the wire to the right front positive speaker output.Gray

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

From the 8-pin subwoofer harness to the aftermarket radio (ampliﬁed models only):

• Connect the RCA to the subwoofer output. White

12-pin pre-wired AXSWC harness:

• This harness is to be used along with the optional AXSWC (not included) to retain steering

wheel audio controls. If the AXSWC is not being used, disregard this harness. If it will be

used, please refer to the AXSWC instructions for radio connections and programming.

Disregard the harness that comes with the AXSWC.

• For the CR-V 2014: If the vehicle is equipped with Bluetooth controls, and desired to be

retained, connect the Gray/Blue wire to the Yellow wire (pin-15) in the 32-pin harness at the

factory Bluetooth module located in the center of the dash, below the radio.

Produkt Specifikationer

Mærke:	AXESS
Kategori:	Ikke kategoriseret
Model:	AXHN-1

Har du brug for hjælp?

Hvis du har brug for hjælp til AXESS AXHN-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret AXESS Manualer

AXESS AXBUCH-MZ6V Manual

29 Juli 2025

AXESS AXABH-CH3 Manual

29 Juli 2025

AXESS AXDSPX-HK5 Manual

25 Februar 2025

AXESS AXAMP-CH8 Manual

25 Februar 2025

AXESS AXTC-MZ1 Manual

25 Februar 2025

AXESS AXBUCH-TYCAM26V Manual

25 Februar 2025

AXESS AXAMP-FD2 Manual

25 Februar 2025

AXESS AXBUCH-TYCAM36V Manual

25 Februar 2025

AXESS AXAMP-TY1 Manual

25 Februar 2025

AXESS AXAMP-TY4 Manual

25 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech MIC-711-OX Manual

30 Juli 2025

Intellinet 713108 Manual

30 Juli 2025

Electro Harmonix EU12AC-1000 Manual

30 Juli 2025

Advantech PCIE-1753 Manual

30 Juli 2025

MXR Rockman X100 Manual

30 Juli 2025

MIPRO MI-909R Manual

30 Juli 2025

Advantech AMAX-4870 Manual

30 Juli 2025

Advantech IDK-1112P-50XGA2 Manual

30 Juli 2025

MIPRO MP-820 Manual

30 Juli 2025

Advantech ARES-12290 Manual

30 Juli 2025