AXESS AXHN-2 Manual

AXESS Ikke kategoriseret AXHN-2

Læs gratis den danske manual til AXESS AXHN-2 (16 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 93 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 47 anmeldelser. Har du et spørgsmål om AXESS AXHN-2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
AXHN-2
I N S T A L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2023 METRA ELECTRONICS CORPORATION REV. 6/30/23 INSTAXHN-2
Product Info
INTERFACE FEATURES
INTERFACE FEATURES
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties
TABLE OF CONTENTS
Connections
- For models without a factory amp....................2
- For models with a factory amp 3 .........................
Installation 4 .............................................................
Programming 4 .........................................................
Extra settings 5 .........................................................
Honda LaneWatch Camera Retention
2014-2017
APPLICATIONS
• Provides accessory power (10-amp)
• Provides NAV outputs (parking brake, reverse, speed sense)
• Pre-wired AXSWC harness (AXSWC sold separately)
• Retains the factory backup camera
• Retains the LaneWatch camera
• Retains ability to change factory clock and date*
• Retains the factory AUX-IN jack
• Can be used in non-amplified, or amplified models
• Retains balance and fade
• Micro-B USB updatable
• AXHN-2 interface
• AXHN-2 harness
Honda
Civic 2014-2015 ...................................................................................................
CR-V 2015 ...........................................................................................................
FIT 2015-2017 .....................................................................................................
* Excluding LX and NAV models
Visit
AxxessInterfaces.com
for up-to-date vehicle specific applications.
Visit for more detailed information about the product and MetraOnline.com
up-to-date vehicle specific applications
2
CONNECTIONS
For models
without
a factory amp:
From the AXHN-2 harness to the aftermarket radio
Main harness:
• Connect the wire to the ground wire.Black
• Connect the wire to the battery wire.Yellow
• Connect the wire to the accessory wire.Red
For the following (8) connections, cut off the RCA jacks to expose the speaker wire inside.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
• Connect the wire to the right front positive speaker output.Gray
• Connect the wire to the right front negative speaker output.Gray/Black
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative speaker output.Purple/Black
16-pin harness:
• Connect the wire to the illumination wire.Orange/White
The following (3) wires are for aftermarket multimedia/navigation radios that require these wires:
• Connect the wire to the parking brake wire (if applicable).Light Green
• Connect the wire to the speed sense wire (if applicable).Blue/Pink
• Connect the wire to the reverse wire (if applicable).Green/Purple
• Connect the RCA jack to the backup camera input.Yellow
This RCA jack is used to retain the backup camera as well as the LaneWatch camera.Note:
• Connect the and RCA jacks to the audio AUX-IN jacks (if applicable).White Red
8-pin harness:
• Disregard the RCA jack, it will not be used in this application. White
12-pin pre-wired AXSWC harness & 3.5mm jack:
• This harness and 3.5mm jack is to be used along with the optional AXSWC (sold separately) to
retain steering wheel audio controls. If the AXSWC is not being used, disregard this harness. If
it will be used, refer to the vehicle specific AXSWC instruction from Axxess Interfaces for radio
connections and programming. Disregard the harness that comes with the AXSWC.
• The Gray/Blue wire will only be used in vehicles equipped with Bluetooth. Connect this wire
to the wire in pin-15 from the 32-pin harness in the factory Bluetooth module.Yellow
Bluetooth module location:
Civic - Behind glovebox
CR-V - In dash, under radio
Continue to Installation

Produkt Specifikationer

Mærke: AXESS
Kategori: Ikke kategoriseret
Model: AXHN-2

Har du brug for hjælp?

Hvis du har brug for hjælp til AXESS AXHN-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret AXESS Manualer

AXESS

AXESS AXDSPX-HK3 Manual

22 August 2025
AXESS

AXESS AXDSPX-FD2 Manual

22 August 2025
AXESS

AXESS AXDSPX-HN3 Manual

22 August 2025
AXESS

AXESS AXI-RGB3 Manual

22 August 2025
AXESS

AXESS AXI-MBEIRC-R Manual

22 August 2025
AXESS

AXESS AXDSPX-GL10 Manual

22 August 2025
AXESS

AXESS AXDSPX-HK2 Manual

22 August 2025
AXESS

AXESS AXDSPX-GM31 Manual

22 August 2025
AXESS

AXESS AXI-FL24-R Manual

22 August 2025
AXESS

AXESS AXUSB-CBL Manual

22 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Stiebel Eltron

Stiebel Eltron DHE 24 SLi Manual

27 September 2025
Neets

Neets Touch Panel 4” Manual

27 September 2025
Sanus

Sanus CFR1610 Manual

27 September 2025
Neets

Neets 310-0111 Manual

27 September 2025
Stiebel Eltron

Stiebel Eltron DHB-E 21 SLi electronic Manual

27 September 2025
Stiebel Eltron

Stiebel Eltron CNS 75 F Manual

27 September 2025
Duronic

Duronic DM65W1X1 Manual

27 September 2025
Advantech

Advantech ITA-360 Manual

27 September 2025
Advantech

Advantech AIMB-215 Manual

27 September 2025
Advantech

Advantech IPC-220 Manual

27 September 2025