AXESS AXRC-BW1 Manual


Læs gratis den danske manual til AXESS AXRC-BW1 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 12 anmeldelser. Har du et spørgsmål om AXESS AXRC-BW1, eller vil du spørge andre brugere om produktet?

Side 1/8
AXRC-BW1
I N S T A L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 1/23/20 INSTAXRC-BW1
Product Info
INTERFACE COMPONENTS
INTERFACE FEATURES
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................3
Programming .........................................................3
BMW/Mini Chime Retention 2006-2015
APPLICATIONS
• AXRC-BW1 interface
• AXRC-BW1 harness
• Fuse holder with 96” length of wire
Provides accessory power (12-volt 10-amp)
Retains R.A.P. (retained accessory power)
Provides NAV outputs (parking brake, reverse, and V.S.S)
Retains warning chimes
For non-amplified models, or when bypassing a factory amplifier
Retains balance and fade
Micro-B USB updatable
BMW
1 Series (without amp) 2008-2013
3 Series (without amp) 2006-2013
M3 (without amp) 2007-2013
MINI
Cooper (without amp) 2007-2015
2
CONNECTIONS
From the AXRC-BW1 harness to the aftermarket radio:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the fuse holder with 96” length of wire:
Remove the fuse from the fuse holder.
Connect the 6” long wire side of the fuse holder to the vehicles battery.
Connect the 96” long wire side of the fuse holder to the Yellow wire.
Connect the wire to the accessory wire.Red
Connect the wire to the power antenna wire.Blue
If the aftermarket radio has an illumination wire, connect the wire to it.Orange
Connect the wire to the right front positive speaker output.Gray
Connect the Gray/Black wire to the right front negative speaker output.
Connect the wire to the left front positive speaker output.White
Connect the wire to the left front negative speaker output.White/Black
Connect the wire to the left rear positive speaker output.Green
Connect the wire to the left rear negative speaker output.Green/Black
Connect the wire to the right rear positive speaker output.Purple
Connect the wire to the right rear negative speaker output.Purple/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the VSS/speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Connect the wire to the parking brake wire.Light Green
12-pin pre-wired AXSWC harness:
This harness is to be used along with the optional AXSWC (not included) to retain steering
wheel audio controls. If the AXSWC is not being used, disregard this harness. If it will be
used, please refer to the AXSWC instructions for radio connections and programming.
Disregard the harness that comes with the AXSWC.Note:


Produkt Specifikationer

Mærke: AXESS
Kategori: Ikke kategoriseret
Model: AXRC-BW1

Har du brug for hjælp?

Hvis du har brug for hjælp til AXESS AXRC-BW1 stil et spørgsmål nedenfor, og andre brugere vil svare dig