Baldwin Boulder M512402RENT Manual

Baldwin Låse Boulder M512402RENT

Læs gratis den danske manual til Baldwin Boulder M512402RENT (4 sider) i kategorien Låse. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Baldwin Boulder M512402RENT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Baldwin Hardware Corporation

Mortise Lock Installation Instructions

TOOLS REQUIRED

1 Pencil

2 No. 2 and No. 3 Phillips Head

Screwdrivers

3 No. 1 and No. 2 Slotted Screwdrivers

4 1/8" Allen Head Wrench

5 3/4" Wood Chisel or Corner Chisel

6 Measuring Device

7 Lock Mortising Tool (Recommended)

8 Router and Lock Face Template

Note: In order to successfully install a mortise lock and trim, a minimum of average skill level is required with use of the above listed tools.

Read and understand the provided instructions BEFORE attempting to mark or cut the door and/or frame. If there are any questions

before you begin the installation, phone or visit your nearest Baldwin Distributor or contact the Technical Service Department at Baldwin

at 610.777.7811.

Diagram A

Diagram B

ENTRANCE HANDLESET

ENTRANCE LEVER/KNOB SET

9 Combination Square

10 Awl

11 Hacksaw

12 File (Wood Rasp and Metal)

13 Baldwin Aligning Tool

14 Drill and assorted Drill Bits (1/16", 1/8",

5/16", 3/8", 3/4", 1", 1-1/4")

15 Screw Wax or Soap

16 Powder Chalk, Graphite or Lipstick

CAUTION

Baldwin 2-1/2 and 2-3/4 backset Mortise locks are designed for residential use in UL-listed

fire-rated openings rated for 3-hour maximum. Meets U.S. UL10C (positive pressure) and

CANS-104M80. In the event of fire, lock will be permanently disabled when mechanism reaches

temperatures above 400˚F. Use in accordance with local fire code regulations.

PK 1076A 8/05

Mark the Door Double Check Compatibility

of Door Stile & Trim

Mortise Lock Pocket

For Lock Body

Prepare for Lock Front

Mark the door at 37-1/2"- 40" above finished

floor, or if retrofit, at appropriate location to

coordinate with existing strike preparations.

This will be center line of the lock and will put

the knob/lever at 36" - 39" above the floor.

Make sure that the door stile will accommodate

the intended lock.

Mortise the pocket in the door 1/8" deeper

than the lock being installed. Refer to the

Installation Template Guide Chart (blue

sheet) for exact size of mortise pocket.

Rout for the lock front. Square the Corners.

Determine Hole Pattern

Required for Trim on

Blue Sheet

Determine hole pattern required for trim

using Installation Template Guide Chart

(blue sheet shown). Mark the listed holes on

the yellow lock template (figure 7) enclosed

with the lock. Ensure trim will not interfere with

door stop or extend over door panel or glass.

APrepare for Lock Front

Mortise Lock Handleset Installation Instructions

DOOR CONDITIONS

Left Hand Right Hand

Outside

Left Hand

Reverse Bevel

Right Hand

Reverse Bevel

HAND OF DOOR IS ALWAYS DETERMINED FROM THE OUTSIDE

Here are some rules to follow:

• The outside of an exterior door is the

street or entrance side.

• The outside of a room is the hall side.

• The outside of a single communicating door is the

side from which the hinges are not visible when

the door is closed.

• The outside of a closet door is the room or hall side.

GENERAL NOTES

Paper template is designed for 1-3/4" thick doors. For extra thick

doors, measure backset from center of door edge. Tape supplied

template to the door to locate fastener pattern for lock and trim.

When installing hardware on metal or fiberglass doors, ensure the

door was designed to accommodate mortise locks. If in doubt,

check with your local door distributor or door manufacturer.

Removal of hardware from doors is recommended before painting

and finishing of the door. Allow paint/stain to fully cure before

reinstalling hardware, usually ten days to two weeks. Check paint

manufacturer instructions.

Retain these instructions in a safe place should you need to

disassemble the lock trim or require Baldwin’s assistance.

Produkt Specifikationer

Mærke:	Baldwin
Kategori:	Låse
Model:	Boulder M512402RENT

Har du brug for hjælp?

Hvis du har brug for hjælp til Baldwin Boulder M512402RENT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Låse Baldwin Manualer

Baldwin Bethpage M522402RFD Manual

5 Februar 2025

Baldwin Soho M516402RFD Manual

5 Februar 2025

Baldwin Cody M502402ENTR Manual

5 Februar 2025

Baldwin Bethpage M522402ENTR Manual

5 Februar 2025

Baldwin Cody M504402RFD Manual

5 Februar 2025

Baldwin M512402LFD Manual

5 Februar 2025

Baldwin Cody M504402RENT Manual

5 Februar 2025

Baldwin Boulder M514402RENT Manual

5 Februar 2025

Baldwin Boulder M512402RENT Manual

5 Februar 2025

Baldwin M512076RFD Manual

5 Februar 2025

Låse Manualer

Nyeste Låse Manualer

Lockly Visage Manual

7 Oktober 2025

StarTech.com NANOK-LAPTOP-LOCK Manual

4 Oktober 2025

Aqara Smart Lock D200i Manual

31 August 2025

Aqara Smart Door Lock N100 Zigbee Manual

28 August 2025

StarTech.com SSTDC4D-LAPTOP-LOCK Manual

22 August 2025

Kasp K11030D Manual

21 August 2025

Philips DDL720CCABW Manual

20 August 2025

Philips DDL720CCAKW Manual

19 August 2025

Kensington Microsaver Manual

18 August 2025

Honeywell 8734101 Manual

12 August 2025