Bauknecht BK8I HF58 TUC CH Manual

Bauknecht Opvaskemaskine BK8I HF58 TUC CH

Læs gratis den danske manual til Bauknecht BK8I HF58 TUC CH (28 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Bauknecht BK8I HF58 TUC CH, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/28
ENDaily Reference Guide
1
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.bauknecht.eu/register
4 5 6 7 8 9 10 13 14 1511 12 16 17 18 191 2 3 20 21 22
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Auto Intensive program button with indicator light
4. Auto Mixed program button with indicator light
5. Auto Fast program button with indicator light
6. Rapid program button with indicator light
7. Crystals program button with indicator light/ Self-Clean program - 3 sec. press
8. Prewash program button with indicator light
9. Salt reservoir empty indicator light
10. Rinse Aid reservoir empty indicator light
11. Display
12. Program number and remaining time indicator
13. Closed water tap indicator light
14. DESCALE indicator light
15. PowerClean Pro option button with indicator light
16. Half Load option button with indicator light
17. Extra Dry option button with indicator light/ Settings - 3 sec. press
18. Silent option button with indicator light
19. Sani Rinse option button with indicator light
20. Turbo option button with indicator light
21. Delay option button with indicator light
22. START/Pause button with indicator light
SETTING MENU
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings (Extra Dry ) button for 3 seconds, until you hear
a beep and the display shows „SEt”.
3. After one second the rst available setting (letter „h”) will be displayed.
4. Press Prewash program / PowerClean Pro option buttons to
scroll through the list of available settings (see table below), then press
START/Pause to view and change the value of currently selected
setting.
5. Press Prewash program / PowerClean Pro option buttons to
change the value, then press START/Pause to
save the new value.
6. To change another setting, repeat points 2 and 5.
7. Press ON-OFF or wait 30 seconds to exit the menu.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the control
panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
LETTER SETTING
VALUES
(Default - in bold)
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”)
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 |
4 | 5
NaturalDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Time on the oor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Sound
“1” = On, “0” = O
1 | 0
Internal Lights (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This infor-
mation can be obtained from your local water supplier. The factory setting is “3”.
See „WATER HARDNESS TABLE”.
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to 3. The regeneration process
occurs at the beginning of the cycle with additional fresh water.
• Single regeneration consumes ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.
110 ml), making sure it does
not overow from the dis-
penser. If this happens, clean
the spill immediately with a
dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (Soft) 0 - 6 0 - 10 0 - 7
2 (Medium) 7 - 11 11 - 20 8 - 14
3 (Average) 12 - 16 21 - 29 15 - 20
4 (Hard) 17 - 34 30 - 60 21 - 42
5 (Very hard) 35 - 50 61 - 90 43 - 62
A
B
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: docs.bauknecht.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.
CONTROL PANEL
FIRST TIME USE
DISPLAY ON THE FLOOR
1
3
2
1. Delay Time on the oor - indicator of the time left to the start of the cycle, when the Delay option is set.
2. Salt reservoir empty - indicator light on the oor
3. Remaining Time on the oor - indicator of the time left to the end of the cycle

Produkt Specifikationer

Mærke: Bauknecht
Kategori: Opvaskemaskine
Model: BK8I HF58 TUC CH

Har du brug for hjælp?

Hvis du har brug for hjælp til Bauknecht BK8I HF58 TUC CH stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine Bauknecht Manualer

Bauknecht

Bauknecht BKO PBM Manual

29 Oktober 2025
Bauknecht

Bauknecht B8I HT58 TS Manual

30 September 2025
Bauknecht

Bauknecht BKSV1 FAM Manual

16 September 2025
Bauknecht

Bauknecht BKO FBM Manual

25 August 2025
Bauknecht

Bauknecht B0B D651A X Manual

25 August 2025
Bauknecht

Bauknecht OBFC Ecosilent 8650 Manual

24 August 2025
Bauknecht

Bauknecht OBIC Ecosilent 8650 Manual

16 August 2025
Bauknecht

Bauknecht B7F HS51 X Manual

3 August 2025
Bauknecht

Bauknecht BK6IC11BS7LSA0CH Manual

15 Juli 2025
Bauknecht

Bauknecht BK8IA15AM3TUSC0CH Manual

15 Juli 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Big Chill

Big Chill BC24DWCSNPB Manual

29 Oktober 2025
Gram

Gram DS 6300 Manual

29 Oktober 2025
Haier

Haier HDW13F0PS2 Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCPMB Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCBBCW Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCPSS Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCPSB Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWRCR Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCRSB Manual

29 Oktober 2025
Proline

Proline DWP 1247 WH Manual

25 Oktober 2025