BeamZ F1500 160.510 Manual

BeamZ Vi F1500 160.510

Læs gratis den danske manual til BeamZ F1500 160.510 (46 sider) i kategorien Vi. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om BeamZ F1500 160.510, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/46
Ref. Nr. 160.510
F1500
Fazer with DMX & Controller
INSTRUCTION MANUAL
GEBRUIKSAANWIJZING
BEDIENUNGSANLEITUNG
V1.1
- 2 -
Warning:
- The fazermachine must be placed at least 100 cm away from inflammable materials such as curtains, books,
etc. Make sure that the housing cannot be touched by accident.
- Use only Beamz water-based fluid recommended by your dealer.
- Poor liquid caused permanent damage, bad effect, clogging, spitting of unevaporated liquid etc.
- Never add flammable fluids (oil, gas, perfume) to the fog liquid.
- Always keep enough liquid in the tank.
Use of the device without liquid will cause damage to the pump and heater.
- Do not obstruct the openings on top of the case to guarantee a good ventilation.
- Don’t put any objects on the fazer machine.
- For indoor use only.
- During installation, nobody should stand beneath the mounting area.
- Prior to the first use, have the unit checked by a qualified person.
- The unit contains voltage carrying parts. DO NOT open the fazermachine
- Never plug or unplug the unit with wet hands.
- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.
- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It
needs to be repaired by a qualified technician.
- Only connect this unit to an earthed mains outlet of 220-240Vac/50Hz .
- Always unplug the unit during a thunderstorm or when it is not in use.
- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please
let the unit reach room temperature prior to use.
- When you unplug the unit from the mains always pull the plug, never the lead.
- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a
steel cable, etc. which has to be fastened separately from the mounting bracket.
- The supplied bracket is the main fixing and must be used to solidly mount the light effect.
- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings
must be fulfilled.
- Keep out of the reach of children.
Location
Select a location where it is easy to fill the tank. It is also possible to hang the unit by means of the supplied
holder and fixing screws.
Installation and Use
Unpack the fazer machine. Do not connect yet the net cable. Connect the remote control to the connector on
the back of the fogger.Fill the fluid tank by means of a funnel. Plug the unit into a mains outlet. Thus the heating
element is automatically switched on. Depending on the room temperature, it takes about 4 minutes until the
working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up.
Push the switch once and the fazer machine will produce a nice thick fog. Once the fazer machine has reached
its working temperature (the LED is lit) the fazer machine can produce fog continuously. After this period of time,
the fog generator is cooled so much down that the thermostat switches off. Wait a while until the working
temperature is reached again. It is recommended to produce haze with small pauses in between so that the
temperature is maintained and the thermostat doesn’t switch off.
Make sure that there is always enough liquid contained r machine without liquid can in the tank. Use of the faze
permanently damage the unit. Once the fazer machine generates little haze or pump generate another 'rattling'
sound i turn off the unit direct. Check the fluid level and fill the tank when it is empty, check the hose and filter
blockages and restore it. Plug in the unit and check if the problem is resolved. If problem persists, switch unit
direct off to prevent further damage and contact your dealer.
Switching the unit off
Switch the unit off by unplugging it from the mains. Otherwise the 1500W heating element will draw
unnecessarily current.

Produkt Specifikationer

Mærke: BeamZ
Kategori: Vi
Model: F1500 160.510

Har du brug for hjælp?

Hvis du har brug for hjælp til BeamZ F1500 160.510 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Vi BeamZ Manualer

BeamZ

BeamZ F1500 160.510 Manual

13 Januar 2025
BeamZ

BeamZ F900 160.507 Manual

2 Oktober 2024
BeamZ

BeamZ ICE700 160.514 Manual

31 Juli 2024
BeamZ

BeamZ S500PC 160.432 Manual

29 Juli 2024
BeamZ

BeamZ SNOW 900 Manual

28 Juli 2024
BeamZ

BeamZ ICE1800 160.518 Manual

25 Juli 2024
BeamZ

BeamZ S700 160.438 Manual

24 Juli 2024
BeamZ

BeamZ S1200 MKII 160.491 Manual

21 Juli 2024

Vi Manualer

Nyeste Vi Manualer

Ikea

Ikea BRILJERA 902.575.76 Manual

13 Februar 2025
Ikea

Ikea HULTARP 804.444.42 Manual

3 Januar 2025
Ikea

Ikea KUNGSFORS 403.349.21 Manual

3 Januar 2025
Leatherman

Leatherman Tread Manual

26 December 2024
Hama

Hama 00111541 Manual

1 Oktober 2024
Toolcraft

Toolcraft TC-FC-USB Manual

28 September 2024
Team

Team EM 10 Manual

23 September 2024
Hazet

Hazet 2157 Manual

11 September 2024
Ikea

Ikea JÄMFÖRA 903.468.32 Manual

6 September 2024
Ikea

Ikea VARDAGEN 002.947.19 Manual

6 September 2024