Blaupunkt IR-S1 Manual

Blaupunkt Bevægelsesdetektor IR-S1

Læs gratis den danske manual til Blaupunkt IR-S1 (2 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Blaupunkt IR-S1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Wireless PIR Motion Sensor (IR-S1)
P
P
a
a
r
r
t
t
s
s
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Learn/Test Button & LED indicator
Press the button to transmit a learn/test code and enter Test
mode for 3 minutes. The LED will light up whenever a movement
is detected under Test mode.
2. Battery Insulator
3. Supervision Enable/Disable Jumper Switch
(JP2)
4
. High/Low Sensitivity Jumper Switch (JP3)
5. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening.
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x PIR Sensor
4 x wall plugs and screws
2 x 1.5V alkaline batteries (pre-installed)
Supervision Enable/Disable Jumper Switch (JP2)
If enabled, the PIR sensor will transmit supervision signal to
Control Panel periodically for the sensor to monitor PIR sensor
condition.
Jumper set to ON = supervision function is Disabled (Default)
Jumper set to OFF = supervision function is Enabled
High/Low Sensitivity Jumper Switch (JP3)
Jumper set to ON = PIR sensitivity is set to High
Jumper set to OFF= PIR sensitivity is set to Low (Default)
Put the Control Panel into learning mode, then press the learn
button to transmit learn code. Please refer to Control Panel
manual for to complete the learning process.
The PIR Sensor has knockouts on the back where plastic is
thinner. The 2 center knockouts are for flat wall mounting, and the
4 side knockouts are for corner mounting.
1. Break through the knockouts; use the knockouts to mark
position on the wall or corner.
2. Drill holes into the wall or corner using the knockouts as
template.
3. Fix the PIR Sensor base onto the wall with the screws and
plugs provided.
4. Replace the PIR Sensor cover onto the base.
S
S
l
l
e
e
e
e
p
p
T
T
i
i
m
m
e
e
r
r
The PIR features a “sleep time” of approximately 1 minute for
power conservation. After transmitting a detected movement, the
PIR will not retransmit for 1 minute. Any further movement
detected during this sleep period will extend the sleep time by
another minute. In this way continuous movement in front of a
PIR will not unduly exhaust the battery.
T
T
e
e
s
s
t
t
o
o
d
d
e
e
Press the Test Button to enter Test mode for 3 minutes. Sleep
timer will be disabled under Test mode, and the LED indicator will
flash every time a movement is detected. Use the Test mode to
determine PIR detection coverage and plan the installation
location accordingly.
L
L
E
E
D
D
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
Off Normal Operation
On (2 seconds) - When Tamper Switch is triggered
- Movement detection under low battery,
tamper triggered, or Test mode.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Surface Fixing
Knockouts x 2
(Inside)
Corner Fixing
Knockouts x 4
B
B
a
a
t
t
t
t
e
e
r
r
y
y
The PIR uses two alkaline 1.5 V batteries as its power source. It
also features low battery detection function to notify the Control
Panel when the battery voltage is low.
When PIR is on low battery, follow the procedure below to
change the batteries.
1. Open the PIR back cover.
2. Remove the old batteries.
3. Press the tamper switch several times to fully discharge.
4. Insert the new batteries observing correct polarity. The PIR
LED will light up for 30 seconds to indicate it is warming up.
5. Replace the PIR back cover.
E
E
n
n
v
v
i
i
r
r
o
o
n
n
m
m
e
e
n
n
t
t
a
a
l
l
C
C
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
-10°C to 40°C, relative humidity 85% non-condensing.
R
R
a
a
d
d
i
i
o
o
433 MHz
F
F
C
C
C
C
S
S
t
t
a
a
t
t
e
e
m
m
e
e
n
n
t
t
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
F
F
C
C
C
C
C
C
a
a
u
u
t
t
i
i
o
o
n
n
:
:
To assure continued compliance, any changes or modifications
not expressly approved by the party responsible for compliance
may void the user's authority to operate this equipment. (Example
- use only shielded interface cables when connecting to computer
or peripheral devices).
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n

Produkt Specifikationer

Mærke: Blaupunkt
Kategori: Bevægelsesdetektor
Model: IR-S1

Har du brug for hjælp?

Hvis du har brug for hjælp til Blaupunkt IR-S1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Bevægelsesdetektor Blaupunkt Manualer

Blaupunkt

Blaupunkt IR-S1 Manual

28 Juli 2025
Blaupunkt

Blaupunkt IR-S4 Manual

10 November 2023
Blaupunkt

Blaupunkt IR-P4 Manual

20 December 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Crestron

Crestron GLA-LDL-PC-0-10-WL Manual

9 September 2025
Biltema

Biltema 46-2010 Manual

3 September 2025
Biltema

Biltema 46-2009 Manual

2 September 2025
Leviton

Leviton OSD10-I0I Manual

30 August 2025
Leviton

Leviton OSC04-I0W Manual

30 August 2025
Leviton

Leviton OSC05-M0W Manual

29 August 2025
Leviton

Leviton OSC10-M0W Manual

29 August 2025
Leviton

Leviton OSC20-M0W Manual

29 August 2025
Leviton

Leviton OSC04-IAW Manual

29 August 2025
Leviton

Leviton OSC20-RMW Manual

29 August 2025