Bogen SM4T Manual

Bogen Ikke kategoriseret SM4T

Læs gratis den danske manual til Bogen SM4T (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Bogen SM4T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Easy Install Speaker

Models SM1EZ and SM4T

Speaker Layout

The layout of the speakers should be planned before installation

begins. Layout starts in one corner of the room. The first speaker

should be positioned from each wall a distance approximately equal

to the ceiling height of the room.

The next speaker in row 1should be spaced a distance approxi-

mately equal to twice the height of the ceiling. Each additional speak-

er in the row should use this same spacing.

Row 2 starts at twice the ceiling height distance from row 1and

twice the ceiling height from the wall.The other speakers in this row

are also spaced at twice the ceiling height.

Row 3 is again spaced at twice the ceiling height from the previous

row. The first speaker starting this row is positioned at one ceiling

height distance from the wall (similar to row 1).

Continue this pattern of alternating rows until the room is covered.

Because of the wide sound dispersion characteristic of the SM1EZ

and SM4T, exact placement is not critical. The spacing of the speak-

ers can be adjusted so that the speakers are evenly spaced in a row.

Speaker Installation

Step 2

Step 3

Step 4

STEP 1 - Select amplifier system voltage, 25V or 70V, using the

jumper on the circuit board end, opposite the transformer.

STEP 2 - Position the speaker on the ceiling tile and slowly push the

speaker, forcing the studs through the ceiling tile.

NOTE: When using the SM4T model, set the rotary switch to

the correct wattage tap for the application before mounting

the speaker. Check the back of the SM4T box for the tap set-

tings chart.

STEP 3 - Clean any loose debris or conductive foil from around the

studs. Spin the wide-based wing nuts (supplied) down the

stud.Tighten the wing nuts until they are very snug (finger

tighten only - no tools required). Check that the speaker is

drawn tight to the ceiling tile. Fiberglass sleeves (supplied)

should be placed over the studs at this point to insulate the

exposed portion of the stud as a safety precaution.

STEP 4 - The electrical connections are made to the studs with the

wire nuts (supplied). The studs are color-coded to allow

proper phasing.

Suggested amplifier connections are:

COPPER stud - 70V/25V HOT

NICKEL stud - 70V/25V COMMON

Nylon wire ties (supplied) can be used to secure the speaker wires

to the studs if desired. (Nylon wire ties should wrap around the fiber-

glass sleeve.)

The speaker will also work perfectly well with these connections

reversed. However, it is important to be consistent in the wiring of

the speakers in the system. If adjacent speakers have reversed wiring

connections, they will tend to cancel each other’s bass response,

diminishing the sound quality.

50 Spring Street, Ramsey, NJ 07446, U.S.A.

Tel. 201 1-934-8500, Fax: 20 -934-9832

www.bogen.com

54-5039-01C Printed in China 0503

Specifications subject to change without notice.

Step 1

Produkt Specifikationer

Mærke:	Bogen
Kategori:	Ikke kategoriseret
Model:	SM4T
Højde:	76.2 mm
Vægt:	907.19 g
Produktfarve:	Hvid
Pakkevægt:	1360.78 g
Udgangseffekt (RMS):	4 W
Equalizer:	Ingen
Volumenkontrol:	Dreje
Anbefalet brug:	Andet
Frekvensområde:	125 - 15000 Hz
Forbindelsesteknologi:	Ledningsført
Højttaler, type:	1-vejs
Lyd-output kanaler:	1.0 kanaler
Højttaler, placering:	I væggen/i loftet
Strømkilde type:	Vekselstrøm
Diameter:	241.3 mm
Antal drivere:	1
Diskanthøjttaler:	Ja
Sensitivitet:	90 dB
Bashøjttaler:	Ja
Forstærker:	Ingen
Højttaler kabinet:	Lukket