Bresser OMNI-2 Manual

Bresser Kikkert OMNI-2

Læs gratis den danske manual til Bresser OMNI-2 (2 sider) i kategorien Kikkert. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Bresser OMNI-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

OMNI 2 red dot sights are designed for the ”two eyes open” method which greatly enhances

situational awareness and target acquisition. Thanks to the optical design the red dot

follows the movement of the user’s eye while remaining xed on target, eliminating any need

for centering.

INSTALLING BATTERY

CAUTION: BEFORE YOU BEGIN, ENSURE THAT THE FIREARM IS CLEAR. REMOVE MAGAZINE,

LOCK ACTION OPEN AND VISUALLY INSPECT TO ENSURE THAT THE CHAMBER IS CLEAR.

1. Remove Battery cap, use a coin if needed.

2. Insert Battery with the positive end

toward Battery cap as can be seen in .Fig 1

CAUTION: CHECK THAT THE O-RING IS

IN GOOD CONDITION AND IN POSITION

TO ENSURE THAT THERE WILL BE NO

WATER LEAKAGE INTO THE BATTERY

COMPARTMENT.

3. Replace the cap by pushing down and

screwing on clockwise to tighten

4. Verify that the red dot is visible.

OMNI-2

WATERPROOF RED DOT SIGHT INSTRUCTIONS

CAUTION: BEFORE YOU BEGIN, ENSURE THAT THE FIREARM IS CLEAR. REMOVE MAGAZINE,

LOCK ACTION OPEN AND VISUALLY INSPECT TO ENSURE THAT THE CHAMBER IS CLEAR.

PRODUCT SPECIFICATIONS ILLUMINATION CONTROL

On/O buttons and illumination control is located on the top of the sight. See .Fig 2

1. Press either the ( ) or ( ) button turn the sight on.

2. To turn the sight o press and hold both the ( ) and ( )

button for 1 second.

3. Once the dot is illuminated, you can increase the apparent

brightness by pressing and releasing the ( ) button; or

decrease the brightness by pressing and releasing the ( )

button.

4. When the sight on, the shutdown will automatically turn o

after 3 hours.

5. If red dot sights is shut down due to abnormal power

failure, it will remain in the stall before shutdown when power

is turned on again.

MOUNT ONTO A PICATINNY OR WEAVER-STYLE RAIL

Your OMNI-2 features a durable base design that is factory ready to mount on a Picatinny or

standard Weaver rail system. To get started, refer to the following steps:

CAUTION: BEFORE YOU BEGIN, ENSURE THAT THE FIREARM IS CLEAR. REMOVE MAGAZINE,

LOCK ACTION OPEN AND VISUALLY INSPECT TO ENSURE THAT THE CHAMBER IS CLEAR.

1. Loosen the screw using an allen wrench, and clamp the locking bar around the Picatinny

rail

2. With the shaft positioned in a groove on the

Picatinny/weaver rail, push the sight with mount

forward and tighten the shaft using the tool.

WARNING: TO AVOID POSSIBLE RECOIL INJURY,

BE SURE TO LEAVE ENOUGH SPACE BETWEEN

THE RED-DOT SIGHT EYEPIECE AND YOUR EYES.

CHECK TO SEE THAT YOU ARE ABLE TO SEE

THE FULL FIELD OF VIEW AND RED DOT WHEN

IN A SHOOTING POSITION.

3. Tighten the shaft until a light resistance is

encountered. Proceed with another 1/4 to 1/2

turn until fully tightened.

To get the best performance from your red dot,

it must be mounted properly. If you are not

familiar with mounting a red dot, it is strongly

recommended that you seek the assistance of a

qualied professional.

ZEROING

The sight is delivered with the red dot in a centered position. Normally this means that only

small adjustments are necessary, providing that the weapon rail (Picatinny/Weaver rail) is

properly aligned.

CAUTION: DO NOT CONTINUE TO ADJUST WINDAGE AND ELEVATION MECHANISMS IF YOU

ENCOUNTER RESISTANCE.

1. Turn the switch until the red dot has a suitable intensity to contrast against the target.

2. To access the Elevation adjustment screw and the

Windage adjustment screw, remove the Adjustment cap.

See .Fig 3

3. The Adjustment Cap can be used to turn the

Adjustment screws. Place the knobs on the Adjustment

cap into the recesses on the Adjustment screws.

4. Fig 4 Windage adjustments (See .)

a. To move the point of impact to the right, turn Windage

adjustment screw counter clockwise

b. To move the point of impact to the left, turn Windage

adjustment screw clockwise.

5. Elevation adjustments (See .)Fig 5

a. To move the point of impact up, turn Elevation

adjustment screw counter clockwise.

b. To move the point of impact down, turn Elevation

adjustment screw clockwise.

6. Conrm zeroing by ring at least three shots at a

zeroing target. Check points of impact to conrm accuracy

and repeat above procedure if required.

7. After initial ring, ensure that the sight with mount is

securely installed on the weapon.

CAUTION: NEVER CLEAN THE LENSES WITH FINGERS.

USE LENS PAPER/CLOTH. IF LENS PAPER/CLOTH IS NOT

AVAILABLE:

To clear away debris (sand, grass etc.): blow away the

dirt or rinse with clear water.

To clean lenses: mist up the lenses or rinse with clear

water and clean them with a soft piece of cloth.

Model 23-20100

Description Waterproof Red

Dot Sight

Magnication 1x

Length 2.4”

Width 1.6”

Height 2.5”

Optical Height 1.4”

Weight 0.3lbs

Power Supply CR2032 3V

Lithium Battery

Brightness 1 - 10 Day; 1 - 3 NV

Windage 36 MOA

Elevation 36 MOA

Click Value 1 MOA

Waterproof

(Depth/Time)

1m / 30min

Continue on back

Cut and mail in

Learn about the full range of service your warranty provides.

Registering online is quick and easy!

https://explorescientiﬁcusa.com/product-registration

For products that do not include a serial number, use the product item number followed by the date of purchase

expressed in a six-digit format. For example, a purchase date of January 1, 2018, would be entered as 010118.

Model numbers: Serial numbers:

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Produkt Specifikationer

Mærke:	Bresser
Kategori:	Kikkert
Model:	OMNI-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Bresser OMNI-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kikkert Bresser Manualer

Bresser CONDOR 24-72X100 Manual

7 Juli 2025

Bresser Muskoka 7x50 Manual

19 Juni 2025

Bresser NightExplorer 7x50 Manual

30 Marts 2025

Bresser NightExplorer 15x70 Manual

30 Marts 2025

Bresser Condor 20-60x85 Manual

27 Marts 2025

Bresser OMNI-2 Manual

17 December 2024

Bresser Pirsch 10X34 Manual

11 September 2024

Bresser Digital Nightvision 3x Manual

5 September 2024

Bresser Spotty Manual

31 August 2024

Bresser Pirsch 8X26 Manual

26 August 2024

Kikkert Manualer

Nyeste Kikkert Manualer

Levenhuk Sherman PLUS 10x42 Manual

4 November 2025

BSA Sweet 22 Manual

4 November 2025

Levenhuk Sherman BASE 8x40 Manual

4 November 2025

Levenhuk Sherman BASE 10x40 Manual

4 November 2025

Lenco NVB-010 Manual

3 November 2025

Kite Optics APC 60 Manual

31 Oktober 2025

Pulsar Expert VM 8x40 Manual

11 Oktober 2025

Swarovski Z8i Manual

8 Oktober 2025

Nikon WX 7x50 IF Manual

8 Oktober 2025

PARD Night Stalker 4K Manual

8 Oktober 2025