Canarm CP50 Manual

Canarm Ikke kategoriseret CP50

Læs gratis den danske manual til Canarm CP50 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Canarm CP50, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/10
Page 1 of 6
M-CP 11/24
MODELS: CP50, CP80
The purpose of this manual is to aid in the proper installation and operation of the CP Series exhaust fans. These instructions are intended
to supplement good general practices and are not intended to overwrite local codes and ordinances.
IT IS THE RESPONSIBILITY OF THE PURCHASER TO ENSURE THAT THE INSTALLATION AND MAINTENANCE OF THIS
EQUIPMENT IS HANDLED BY QUALIFIED PERSONNEL.
Inspect all shipments carefully for damage. THE RECEIVER MUST NOTE ANY DAMAGE ON THE CARRIER’S BILL OF LADING AND
FILE A CLAIM IMMEDIATELY WITH THE FREIGHT COMPANY.
For quiet and efficient operation, long life, and attractive appearance - lower or remove grille and vacuum interior of unit with the dusting
brush attachment.
Use this unit only in the manner intended by the manufacturer. If you have questions, 1.
contact the manufacturer at the address or telephone number listed in the warranty.
Before servicing or cleaning unit, switch power off at service panel and lock the service 2.
disconnecting means to prevent power from being switching on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
Installation work and electrical wiring must be done by a qualified person(s) in accordance 3.
with all applicable codes and standards, including fire-rated construction codes and
standards.
Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to 4.
prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 5.
Ducted fans must always be vented to the outdoors. 6.
Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit. 7.
This unit must be grounded. 8.
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 9.
This product is designed for installation in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must point up. 10.
To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 11.
Please read specification label on product for further information and requirements. 12.
Please follow all applicable national, state/provincial and local codes. All of them will supersede this manual. 13.
Failure to follow the safety instructions in this manual may cause serious injury or death due to electrical shock or high 14.
speed rotating parts.
GENERAL SAFETY
CLEANING AND MAINTENANCE
OPERATION INSTRUCTIONS AND PARTS MANUAL
PLEASE READ AND SAVE THESE INSTRUCTIONS
CP SERIES
ULTRA QUIET HIGH
PERFORMANCE EXHAUST FANS
OPERATION INSTRUCTIONS AND PARTS MANUAL
PLEASE READ AND SAVE THESE INSTRUCTIONS
Page 2 of 6
M-CP 11/24
CP SERIES
ULTRA QUIET HIGH PERFORMANCE EXHAUST FANS
Use an on/off switch to operate this fan. See Electrical Wiring Connection section for details.
OPERATION
ASSEMBLY INSTRUCTIONS
1. Do not use in a cooking area.
2. Two ways to connect ductwork to a factory-shipped unit.
PLAN THE INSTALLATION
1. Housing mounted to I-joists - start at Assembly Instructions 1.
2. Housing mounted to joists - start at Assembly Instructions 1.
3. Housing mounted to truss - start at Assembly Instructions 2.
TYPES OF TYPICAL INSTALLATIONS
ROUND
DUCT*
WALL CAP*
(with built-in
damper)
* Purchase
separately
POWER
CABLE*
INSULATION*
(Place around and
over Fan Housing.)
Seal gaps
around
Housing.
ROUND
ELBOW(S) *
Seal duct
joints with
tape.
ROOF CAP*
(with built-in
damper)
Keep duct
runs short
FAN
HOUSING
1. Mount housing to joist or I-joist.
a. Hold the housing so that it is in contact with the bottom of the joist.
b. Attach the housing with four (4) screws to the joist through the holes in
each mounting flange.

Produkt Specifikationer

Mærke: Canarm
Kategori: Ikke kategoriseret
Model: CP50

Har du brug for hjælp?

Hvis du har brug for hjælp til Canarm CP50 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Canarm Manualer

Canarm

Canarm CBFI300 Manual

17 September 2025
Canarm

Canarm C50 Manual

17 September 2025
Canarm

Canarm CNPD100-3 Manual

17 September 2025
Canarm

Canarm CEP110 Manual

17 September 2025
Canarm

Canarm CP50 Manual

17 September 2025
Canarm

Canarm P14-4M Manual

16 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vestil

Vestil E-MT-6 Manual

17 September 2025
Vestil

Vestil LAD-MM-8 Manual

17 September 2025
Vestil

Vestil FLOW-4-3 Manual

17 September 2025
Vestil

Vestil LAD-MM-4-G Manual

17 September 2025
Lakeside

Lakeside 6205 Manual

17 September 2025
Vestil

Vestil AS-383-4PK Manual

17 September 2025
Turbo Air

Turbo Air TBC-80SB-N Manual

17 September 2025
Vestil

Vestil PNU-3060 Manual

17 September 2025
Blodgett

Blodgett Invoq 61BG Manual

17 September 2025
Vestil

Vestil LAD-FM-84-PSO Manual

17 September 2025