Celestron C90 MAK Manual

Celestron Kikkert C90 MAK

Læs gratis den danske manual til Celestron C90 MAK (15 sider) i kategorien Kikkert. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Celestron C90 MAK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/15

C90mm Maksutov Spotting Scope - #52268

Congratulations on your purchase of a Celestron spotting scope! Whether your interest is in sports, bird watching, nature, wildlife, casual astronomy,

or other activities, this spotting scope offers very high optical quality to allow you years of viewing pleasure.

Assembly

To attach the Erect Image Diagonal and an Eyepiece:

1. Remove any caps from the rear of the optical tube, the erect image diagonal, and the eyepiece.

2. Loosen all thumbscrews on the rear part of the optical tube and the erect image diagonal so that the threads do not protrude into the barrels.

3. Slide the chrome portion of the erect image diagonal into the rear of the optical tube as shown in the left image below. Then, tighten the

thumbscrews to hold the erect image diagonal in place.

4. Slide the chrome portion of the eyepiece (use the 32mm) into the erect image diagonal (see right image below). Then, tighten the

thumbscrew to hold the eyepiece in place.

5. To use other eyepieces of varying powers, reverse the installation of the eyepiece above and install other eyepieces. Any 1.25” eyepiece will

work with this spotting scope. Celestron offers a wide selection of optional eyepieces.

To attach the 8x21 Erect Image Finderscope:

The finderscope is an aid to locating objects to view as it is an 8 power instrument with a much wider field of view than the spotting scope itself. The

finderscope itself comes pre-assembled and is mounted inside the bracket of the finderscope.

1. Loosen the thumbscrew on the mounting bracket on the optical tube (left image below).

2. Slide the finder bracket (with finderscope attached) into the mounting bracket on the optical tube (center image below).

3. The finderscope bracket will slide in from the back. The finderscope should be oriented so that the objective lens (larger piece of glass) is

toward the front end of the spotting scope.

4. Tighten the thumbscrew on the mounting bracket to hold the finderscope firmly in place. The finderscope is correctly attached as shown in

the right image below.

Optical Tube Finderscope Eyepiece

Lens Ca

Tripod Adapter

Erect Image

Diagonal

ENGLISH

To Attach your Spotting Scope to a Photo/Video Tripod

Attach your spotting scope to a rigid photo/video tripod before trying to observe as the size and power of the spotting

scope requires a solid tripod to be able to see sharp and steady views. On the bottom of the spotting scope is a tripod

adapter (see image on pg. 1) which has 1/4x20 threaded holes and this will allow you to attach your tripod to the spotting

scope. Celestron offers optional photo/video tripods.

Using your Spotting Scope

Prior to using your spotting scope, remove the front lens cap.

Warning Note: Never look directly at the Sun with the naked eye or with your spotting scope as eye damage may result.

The C90 spotting scope focusing mechanism controls the position of the primary mirror which slides back and

forth on the primary baffle tube. Turn the focusing knob (see image to the left and the knob is located in the

bottom right area) until the image is sharp. If the knob will not turn, the primary mirror has reached the end of its

travel on the focusing mechanism. Turn the knob in the opposite direction until the image is sharp. Once an

image is in focus, turn the knob clockwise to focus on a closer object and counterclockwise for a more distant

object. A single turn of the focusing knob moves the primary mirror only slightly. Therefore, it will take many

turns to go from close focus (approximately 15 feet) to infinity. For astronomical viewing, out-of-focus star

images are very diffuse making them difficult, if not impossible, to see. If you turn the focus knob too quickly,

you can go right through focus without seeing the image. For best results, your first astronomical target should

be a bright object (like the Moon) so that the image is visible even when out of focus.

Note: If changing eyepieces to use different powers on the same subject, you will have to refocus.

Aligning the Finderscope:

1. To make things a little easier, you should align the finderscope during the day when it is easier to locate objects.

2. Choose a conspicuous object that is over 500 yards away. This will eliminate any possible parallax effect.

3. Point your spotting scope at the target and center it in the main optics of the spotting scope (using the 32mm eyepiece).

4. Check the finderscope to see where the object is located in the field of view.

5. Adjust the three small thumbscrews on the finder bracket, tightening one while loosening another, until the cross hairs are centered on the target.

Accurate alignment of the finder will make it much easier to find objects in the main optical tube.

Note: If the image is not sharp (out of focus) with the finderscope, rotate the eyepiece end of the finderscope until you achieve a sharp focus.