Chamberlain 041-0180-000 Manual


Læs nedenfor 📖 manual på dansk for Chamberlain 041-0180-000 (6 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 38 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/6
Wire Harness Replacement
Repair Parts 041-0180-000, 041-0181-000
To prevent possible SERIOUS INJURY or DEATH:
Disconnect ALL electric and battery power BEFORE performing ANY
service or maintenance.
To prevent damage to the receiver/logic board, DO NOT touch printed
circuit board of replacement receiver/logic board during installation.
ALWAYS wear protective gloves and eye protection when changing the
battery or working around the battery compartment.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Introduction
Use this instruction to replace the integrated LED light module cover. The
images throughout this manual are for reference only and your product may
look different.
You will need:
1/4" magnetic nut driver
Long-nosed pliers
5/16" long-shafted magnetic nut driver and socket
Flathead screwdriver
Instructions
The images throughout this manual are for reference only and your product
may look different.
1. Disconnect the electrical and battery power (if applicable) to the garage
door opener. Remove the battery and place in a safe location.
2. Remove the control door panel from both ends of the opener.
Refer to . Figure 1
a. Squeeze or separate
hinges depending on the
style of operator.
b. Remove the control door
panel from the hinge
setting, and place in a
safe location.
3. Disconnect the door control
wires from the RED and
WHITE terminals and the
Safety Reversal Sensor wires
from the BLACK and WHITE
terminals. . Figure 2
4. Remove the end panels from
both ends of the opener.
5. Remove decorative ring
from opener (applicable
units). .Figure 3
6. Remove the integrated LED
light module cover from the
opener. .Figure 4
7. Disconnect the ORANGE and
WHITE wire harness from
plug to the Integrated LED
light module and set aside cover / integrated LED light module. Figure 4
(A).
8. Remove the wire harness:
a. Unplug the 4-wire harness (ORANGE, BLACK, WHITE, GREEN) from the
receiver logic board. .Figure 4 (B)
b. Unplug the WHITE and BLACK wires from the terminal block.
Refer to .Figure 5
c. Remove the GREEN
ground wire.
8. Attach the new wire harness.
a. Attach the ORANGE and
WHITE wire harness from
plug to the integrated LED
light module.
b. Attach the GREEN
ground wire.
c. Plug in the 4-wire harness
(ORANGE, BLACK, WHITE,
GREEN) from the receiver
logic board. . Figure 3 (B)
d. Plug in the WHITE and
BLACK wires from the
terminal block.
e. Bundle and fasten the wires
together with a wire tie.
9. Attach integrated LED light
module.
10. Attach both end panels.
11. Attach decorative ring (applicable units).
12. Reconnect the door control and Safety Reversal Sensor wires. . Figure 2
Door control:
WHITE wire into the WHITE terminal.
WHITE/RED wire into the RED terminal.
Safety Reversal Sensors:
WHITE wires into the WHITE terminal.
WHITE/BLACK wires into the GRAY terminal.
13. Reattach the control door panels.
14. Reconnect power to the opener.
15. Test the Safety Reversal System. Refer to the Owner’s Manual.
RED
WHITE
WHITE
GREY
Figure 2
Figure 3
Figure 1
A
B
Figure 4
Figure 5
Integrated LED Light Module
Control Door Panel
End Panel
Terminal
Block
Black
Wire
White
Wire
Terminal
Block


Produkt Specifikationer

Mærke: Chamberlain
Kategori: Ikke kategoriseret
Model: 041-0180-000

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain 041-0180-000 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Chamberlain Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer