Chamberlain 041D8006-1 Manual

Chamberlain Ikke kategoriseret 041D8006-1

Læs gratis den danske manual til Chamberlain 041D8006-1 (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 62 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 31.5 anmeldelser. Har du et spørgsmål om Chamberlain 041D8006-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE

performing ANY service or maintenance.

The garage door MUST be in the fully closed position during

installation.

ALWAYS wear protective gloves and eye protection when

changing the battery or working around the battery

compartment.

MODELS 041D1739-1, 041D1624-1

AND 041D8006-1

INTRODUCTION

The images throughout these instructions are for reference and

your product may look different.

You will need:

• 1/4" magnetic nut driver

• Long-nosed pliers

• 5/16" long-shafted magnetic nut driver and socket

• Flathead screwdriver

INSTALLATION

1. Close the garage door. Unplug the garage door opener. Disconnect the battery (if applicable).

2. Disengage the door by pulling the emergency release handle. Loosen the chain/belt tension by loosening the nut.

3. For belt, remove the sprocket cover by removing the screws. Remove the belt from the sprocket.

For chain, remove the sprocket cover by squeezing the sides then pulling up. Remove the chain from the sprocket.

4. Use a flathead screwdriver to remove the C-clip from the motor shaft, then remove the sprocket from the motor shaft (set the

sprocket and C-clip aside to reinstall later).

Motor Kit for DC Garage Door Openers

Nut

BELT - Trolley Type A

CHAIN - Trolley Type A

BELT - Trolley Type B

CHAIN - Trolley Type B

Nut

BELT CHAIN

Sprocket

Cover

Sprocket

Cover

C-Clip

Sprocket

Battery

Emergency

Release Handle

Emergency

Release Handle

Emergency

Release Handle

Emergency

Release Handle

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer

or birth defects or other reproductive harm. For more information

go to www.P65Warnings.ca.gov

INSTALLATION

5. Disassemble the garage door opener:

• Remove the light lens (if applicable).

• Disconnect the wires from quick-connect terminals on the logic board.

• Remove the end panel with the logic board.

• Disconnect all wire harnesses from the logic board.

• Remove the cover.

• Remove the motor assembly from the chassis.

• Remove the wire harness from the travel module on the old motor assembly. Discard the old motor assembly.

6. Reassemble the garage door opener:

• Secure the new motor assembly to the chassis. (If screws are provided with the new motor assembly, use them. If screws are

not provided, use the screws from the old motor assembly.)

• Attach the old travel module wire harness to the travel module on the new motor assembly.

• Reattach all the wire harnesses to the logic board (be sure the tabs on the wire harnesses are facing the end panel, not the logic

board).

• Reattach the cover, then the end panel.

• Reconnect the wires to the quick-connect terminals.

• Reattach the light lens.

• Reattach the sprocket and use the C-clip to hold the sprocket in place.

• Reattach the belt/chain to the sprocket.

• Reattach the sprocket cover.

7. Re-engage the door. NOTE: Make sure the inner trolley engages with the outer trolley.

8. Set the belt/chain tension:

• For chains with trolley type A, tighten the nut until the chain is a 1/4 inch (6 mm) above the base of the rail at the of midpoint

the rail.

• For chains with trolley type B, tighten the nut until the chain is a 1/2 inch (13 mm) above the base of the rail at the of midpoint

the rail.

• For belts with trolley type A or B, tighten the nut until the spring is as close to 1-1/4" (3.18 cm) as possible.

9. Connect power.

Proceed to Adjustments.

Tabs

Wire Harnesses

Logic Board

End Panel

Quick-Connect Terminals

To insert or remove the

wires from the terminal,

push in the tab with a

screwdriver tip.

End Panel

Travel Module

Wire Harness

Cover

Light Lens

Motor Assembly

1-1/4"

(3.18 cm)

1/4"

(6 mm)

1-1/4"

(3.18 cm)

1/2"

(13 mm)

Outer Trolley

Inner Trolley

Outer Trolley

Mid Length of Rail

Safety Reversing

Sensors

Door Control

BELT - Trolley Type A BELT - Trolley Type B

CHAIN - Trolley Type A CHAIN - Trolley Type B

Produkt Specifikationer

Mærke:	Chamberlain
Kategori:	Ikke kategoriseret
Model:	041D8006-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain 041D8006-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Chamberlain Manualer

Chamberlain CHU48C Manual

12 August 2025

Chamberlain RA8001 Manual

3 Juli 2025

Chamberlain CH363C Manual

19 Juni 2025

Chamberlain CH348C Manual

18 Juni 2025

Chamberlain 041A8420 Manual

13 Januar 2025

Chamberlain RZ94-05 Manual

1 Januar 2025

Chamberlain PILCEV-P1 Manual

7 Oktober 2024

Chamberlain RTX8P Manual

2 Oktober 2024

Chamberlain MYQ-G0201 Manual

2 Oktober 2024

Chamberlain 041D9204 Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Turbo Air TBC-65SB-N6 Manual

2 September 2025

Speco Technologies N4WNRMM Manual

2 September 2025

Fromm & Starck STAR_FR_04 Manual

2 September 2025

XPower BR-282A Manual

2 September 2025

Grunkel SAN-GRILLNG Manual

2 September 2025

Phoenix Contact BL2 PPC AIO65 7000 Manual

2 September 2025

AVer DL10 Manual

2 September 2025

Panduit C2CAC06ABWPAB1 Manual

2 September 2025

Rigol HDO1204 Manual

2 September 2025

XPower A-2B Manual

2 September 2025