Chamberlain 050ACTWFATSMC Manual

Chamberlain Ikke kategoriseret 050ACTWFATSMC

Læs gratis den danske manual til Chamberlain 050ACTWFATSMC (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 69 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 35 anmeldelser. Har du et spørgsmål om Chamberlain 050ACTWFATSMC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/12
1
To insert or
remove the wires
from the terminal,
push in the tab with
a screwdriver tip.
Red
White
Grey
White
DANGER PELIGRO
132C2280-3D
TO ER ASE AL L
RECEIVER CODE S
1. Press and HOLD
receiv er ora nge
ERASE button
6 seco nds . Indicato r
light will tu rn ON.
2. Releas e bu tton
when lig ht turn s OFF .
CANADA:
PART NO.: NO. DE PIEZA:
DATE:
THE CHAMB ERLAI N
GRO UP, IN C., USA
Ensa mblad o en México
Ass emble d in Mex ico
ELIMINA CIÓN DE
TODOS LOS CÓDIGOS DE L
RECEPT OR
1. MANT ENGA PRESIONADO
el bo tón na ranja "ERASE"
del re ceptor dura nte 6
seg undo s. La luz de l
indicador se encenderá.
2. Suelte e l botón cuand o la
luz se apague.
DANGER PE LIGRO
132C2280-3D
TO ERASE A LL
RECEIVE R C ODE S
1. Press and H OLDreceiver orange
ERASE butto n
6 seconds. In d i cato r
ligh t wi ll tu rn ON .
2. Release butt o n when l ig h t t u rn s OFF .
CANADA:
P : PIEZ A:ARTN O. NO.DE
DATE:
THE CHAM BERLAIN GROU IN C.,U SAP,
Ensamblado en M éxi co
Assembled in M exi co
ELIMINA CIÓ N DE
TODOSLOS CÓDIGOS DEL
RECEPTOR
1. MANTENGAPRESIONADOel botón n aranj a "ERASE"
del recepto r d u ran te 6
segund o s. La lu z d el
indi cado r se en cend erá.
2. Suelte el b o tón cu an d o la
luz se apag u e.
Before you begin
1
Installation
RECEIVER LOGIC BOARD REPLACEMENT
Model 050ACTWFATS
1.2 To maintain your warranty, place the
provided label over the existing label
on the end panel of the door operator.
Place the STEP SAVER SETUP label on
the end panel directly below the yellow
LEARN button.
1.1 Remove the light lens by pulling the
top sides of the light lens and rotate the
light lens down. Squeeze the light lens
clips to remove lens from end panel.
Your new myQ® serial number is located on the replacement label with your replacement logic board. You will need this new myQ ® serial number to connect your operator to the network. You will also
have a STEP SAVER SETUP label that must be adhered to your end panel directly under the yellow LEARN button for future identification. This second label indicates your board has been updated, and a
new Product Label should be placed over the current Product Label. Your product may look different.
1.3 Disconnect power to the door operator.
Remove the receiver logic board
2
2.1 Disconnect the wires from the quick-connect terminals ( ). A
Remove the receiver logic board end panel from the door
operator.
2.2 Unplug the wire harnesses from the receiver logic
board. You may need needle-nosed pliers to remove
the harnesses.
To prevent possible SERIOUS INJURY or
DEATH:
• Disconnect ALL electric and battery
power BEFORE performing ANY service
or maintenance.
To prevent damage to the receiver/logic
board, DO NOT touch printed circuit board
of replacement receiver/logic board during
installation.
ALWAYS wear protective gloves and eye
protection when changing the battery or
working around the battery compartment.
2.3 Remove the receiver
logic board from the
end panel by removing
the 2 screws and
releasing the 2 clips.
Screws
Wire clip
Clips
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth
defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
A
2
Rojo
Blanco
Gris
Blanco
Rouge
Blanc
Gris
Blanc
Red
White
White
Grey
Install new receiver logic board
3
3.3 Reinsert the wires.
Door control wires:
• white wire into the white terminal.
• white/red wire into the red terminal.
Safety sensor wires:
• white wires into the white terminal.
• white/black wires into the
grey terminal.
NOTE: A test of the safety reverse system is necessary for safe operation.
To insert or remove the
wires from the terminal,
push in the tab with a
screwdriver tip.
3.4 Install the light lens by aligning with
the hinges and snapping into place.
Reconnect power.
NOTE: When installing the light lens, ensure the
antenna wires are hanging straight down.
3.2 Insert the antenna wires through
the holes in the end panel. Snap the
receiver logic board into place on the
end panel and fasten with screws.
NOTE: Some
models will require
the short antenna
wire to be placed in
the traps of the end
panel.
Antenna wires
Antenna
wires
3.1 Connect the wire harnesses to the
new receiver logic board. When
reconnecting the wire harness, be sure
the tabs on the wire harness are facing
the end panel, not the logic board.
Tabs
Harness
End Panel
Wire Clip
Logic Board
Wire
NOTE: If your logic board
has a wire clip, use the
wire clip to hold wires to
the logic board.
DANGER PELI GRO
132C2280-3D
TO A L L ERASE
RECEIVER CODES
1.Pressand HOLD
receiverorange
ERASE button 6 seconds.Indicator
light will turnON.
2.Releasebutton whenli ghtturnsOFF .
CANADA:
P : PIEZA:ARTNO. NO. DE
DA:TE
THECHAMBERLAIN
GROUP, I NC., USA
Ensamblado Méxi co en Assembled M exi co in
ELIMINACIÓN D E
TODOSLOS CÓDIGOS DEL
RECEPTOR
1.MANTENG APRESIONADO
elbotónnaranja "ERASE"
delreceptordurante6 segundos.La del luz
indicadorseencenderá.
2.Suelteelbotóncuando la
luz apague. se
132C2280-3D
receiver orange
ERASE button
Assembled Mexico in
1. AMANTENGPRESIONADO
1
Programming
1.1 Press and release the Learn button on the door operator. The Learn indicator light will glow
steadily for 30 seconds.
1.2 Within 30 seconds, press and hold the
button on the remote control.
1.3 Release the button when the door
operator light blinks. It has learned the
code. If light bulbs are not installed, two
clicks will be heard.
Program a remote control using the learn button (not included)
Learn
Indicator
Light
Yellow Learn
Button
To program the Wi-Fi door operator to your network refer to your owner’s manual.

Produkt Specifikationer

Mærke: Chamberlain
Kategori: Ikke kategoriseret
Model: 050ACTWFATSMC

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain 050ACTWFATSMC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Chamberlain Manualer

Chamberlain

Chamberlain CHU48C Manual

12 August 2025
Chamberlain

Chamberlain RA8001 Manual

3 Juli 2025
Chamberlain

Chamberlain CH363C Manual

19 Juni 2025
Chamberlain

Chamberlain CH348C Manual

18 Juni 2025
Chamberlain

Chamberlain 041A8420 Manual

13 Januar 2025
Chamberlain

Chamberlain RZ94-05 Manual

1 Januar 2025
Chamberlain

Chamberlain PILCEV-P1 Manual

7 Oktober 2024
Chamberlain

Chamberlain RTX8P Manual

2 Oktober 2024
Chamberlain

Chamberlain MYQ-G0201 Manual

2 Oktober 2024
Chamberlain

Chamberlain 041D9204 Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Royal Catering

Royal Catering RCBM_GN1/1_2 Manual

15 August 2025
MSW

MSW -EDGE-L1AG Manual

15 August 2025
Sauermann

Sauermann HM 110 Manual

15 August 2025
ORCA

ORCA Mystic Manual

15 August 2025
Miller Lite

Miller Lite MLIC54 Manual

15 August 2025
Advantech

Advantech ARK-1220L-S6A2 Manual

15 August 2025
Advantech

Advantech UNO-348-1 Manual

15 August 2025
Royal Catering

Royal Catering RCBM-4B Manual

15 August 2025
Advantech

Advantech ADAM-6750-A Manual

15 August 2025
MSW

MSW -ISU-WOOL-2B Manual

15 August 2025