Chamberlain CLDM1 Manual

Chamberlain Ikke kategoriseret CLDM1

Læs gratis den danske manual til Chamberlain CLDM1 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Chamberlain CLDM1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

CLOSED

OPEN

Indoor Receiver

AC Adapter

Sensor

CR203 2

3 VOL TS

Lithium Battery

(CR2032 type)

Double-Sided

Fastening Strip

To prevent possible SERIOUS INJURY or DEATH from a closing garage

door:

• Activate door ONLY when it can be seen clearly, is properly adjusted,

and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER

permit anyone to cross path of closing garage door.

WARN

WARNWARNING

ING

INGING

GARAGE DOOR

MONITOR SYSTEM

PRE-INSTALLATION SYSTEM TEST

1. The sensor and receiver are pre-matched (programmed) at the

factory. Test the system by flipping the sensor over while it is a

few feet away from the receiver. The receiver will show a

green light for closed when the sensor is face up in the vertical

position with the of the case pointing down round end

(Figure 1). The red light will flash when the sensor is face

down in the horizontal position (Figure 2).

2. If the green or the red receiver lights do not come on, or do

not react as described, see the Troubleshooting or Learning

section of these instructions.

INSTALLING THE BATTERY IN THE GARAGE

DOOR INDICATOR SENSOR

1. Place the screw driver blade on the tab at

the end of the case and gently press down

and in toward the case.

2. Insert the the lithium battery into the battery

clip with the + (positive) side face up.

3. Push the case back together tightly by

inserting the top hooks into the back cover,

then snap shut the bottom of

the case.

NOTE: It is normal to hear a rattle from the tilt switch in the sensor

when tilted or rotated to another position.

INDOOR RECEIVER SETUP

1. Plug the AC adapter into any

standard 110 volt AC electrical

wall outlet and the small plug

into the back of the indoor

receiver.

2. The receiver has a 9" antenna

wire which comes out the

back. The antenna should be

straight and not touching

metal.

V OL

Figure 1 Figure 2

NOTE: Because radio control devices are inherently susceptible

to RF interference, this product should NOT be used as a

stand-alone security device. This product is considered a

monitoring and notification device ONLY, and as such, should not

be used as a substitute for a dedicated home security system.

To ensure that your Garage Door Monitor continues to operate

properly, the following checks should be performed on a

monthly basis:

• Check that the sensor is mounted properly on the garage door

(see Mounting the Sensor section of this manual.)

• Ensure the 3 volt lithium battery is installed properly.

• Check to see that the receiver system is plugged into a wall

outlet and the jack is properly connected to the back of the

receiver. Make sure the antenna is straight and not in contact

with any metal objects.

• Check that the receiver is properly recognizing sensor

signals (see Troubleshooting section of this manual.)

CL OSE D

Antenna Learn

Button

Adapter

Location

Garage Door Monitor

Model CLDM1

MOUNTING THE SENSOR

Attach the sensor to the inside of the garage door using the

double-sided fastening strip. Mount the sensor near the top of the

garage door for best results. The round end of the case should

be pointing down when the garage door is closed.

Inside of Garage

Double-Sided Fastening Strip

Round End

Down

Know when your garage door is open

or closed!

Thank you for purchasing the Chamberlain Garage Door Monitor.

Monitor the status of your garage door from inside your home. No

longer will you have to run downstairs or go outside just to see if

you or your children have left the garage door open.

Produkt Specifikationer

Mærke:	Chamberlain
Kategori:	Ikke kategoriseret
Model:	CLDM1
Strømforbrug:	50 mA
Boks design:	Kabinet
Maksimale antal døre:	4 dør(e)
Indbygget UPS:	Ingen
Antal koder:	254