Cioks DC7 Manual

Cioks Ikke kategoriseret DC7

Læs gratis den danske manual til Cioks DC7 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Cioks DC7, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Version 1.1 February 2019 Version 1.1 February 2019

Powering dierent pedal types

Each individual rig is dierent, therefore if you have questions about using the DC7 please e-mail your ,

detailed questions including the power requirements of your specic pedals directly to . support@cioks.com

Technical specications

AC mains input: -265VAC, 50-60Hz max. 58W 90 ,

Outputs 1-7: 9V DC / 0mA 66 or

12V DC / 500mA or

15V DC / 400mA or

18V DC / 330mA each

USB outlet: 5V DC / max. 1A

AUX outlet: 24V DC / max. 2A

Total output power: 48W

Size: 25,4 (excl. rubber feet) 160 8xx8 mm / 6.3x3.5x1.0”

Weight: 0,5kg / 1.1 lb

Warranty period: 5 years worldwide

What’s in the box?

• CIOKS DC7 power supply

• Mains power cord

• 12 Flex cables

• Mounting hardware (2 screws and a hex-key)

• Manual

• Product sheet (drill guide)

• Flex guide

User’s Manual

Version 1 1. – February 2019

Introduction

Since 1991, the Danish company CIOKS has been providing guitar and bass players with reliable power

supplies dedicated for eect pedals. After more than a quarter of a century, CIOKS s designed the next ha

Future Power Generation professional power supply dedicated powering up to seven high current to

pedals (as well as others with lower current draw ongside providing power for a smartphone or a tablet ) al

via the USB outlet and having a 24V DC auxiliary outlet. The result is CIOKS DC7.

Features

• Trim 1-inch prole (25,4mm), only 0,5kg (1.1 lb)

• 2-stage switch-mode power supply topology

• Ultra-low noise achieved by multi-stage ltering

• 7 isolated DC-outlets, 6W each (660mA at 9V on each outlet)

• 4 selectable voltages on each outlet (9, 12, 15 or 18V)

• Charge your phone or tablet with 5V USB outlet (max. 1A)

• Expand via 24V AUX outlet with CIOKS 8 or CIOKS 4 units for more isolated outlets

• Individual status LED on each outlet and global status LED

• Built-in true power meter showing the total load

• Total maximum output power 48W

• Use anywhere in the world, universal mains input voltage 90-265V AC

• Mounting hardware for Pedaltrain and Temple Audio boards included

• Compatible with CIOKS GRIP for drill-free Pedaltrain mounting

• 12 Flex cables included

• Designed in Denmark, assembled in Poland

• 5-year worldwide warranty

Version 1.1 February 2019 Version 1.1 February 2019

Overview

Left

On the left side you ll nd the AC mains input as a standard IEC C14 socket and outlets 1-3 for wi

powering pedals.

Right

On the right side you have outlets 4-7, the 5V USB outlet and the 24V AUX outlet.

Top

CIOKS logo has a red LED placed in the middle of the letter ‘O’ and this functions as a global status

indicator For each outlet you have a voltage selector switch and an advanced LED indicator. The three .

LEDs in the true power meter is also situated on the top of the enclosure. A legend in the middle shows the

voltage switch settings with corresponding output voltage values and the maximum current rating at the

selected voltage.

Front

The two holes in the front with metric M4 threads are to be used with the GRIP bracket (sold separately)

for mounting to Pedaltrain boards with no drilling required.

Bottom

The four detachable rubber feet are situated on the bottom of the enclosure. On this same surface you will

nd 3 holes with metric M4 threads, which should be used for mounting of the power supply to a

pedalboard.

Getting started

Connect the mains power cord to the power supply and AC mains. Set the output voltage for a given outlet

to either 9, 12, 15 or 18V depending on the needs of the particular pedal to be powered. Using the right

Flex cable type connect your pedal to th outlet. Repeat this with your remaining pedals. is

Advanced LED Monitoring feature

Each isolated outlet has its individual LED status indicator. The indicator is lit in normal operation. The

LED light gets dim when you operate just on the higher edge of the current mA limit for the voltage you

have chosen on the given outlet. If you overload or short circuit an outlet, the respective LED indicator

turns o. The light intensity of the status LED will be higher when the output voltage is set to higher a

value than 9V being 12, 15 or 18V.

True power meter

The three small 2mm LEDs on top of the DC7 form a true power meter showing the total load of the power

supply. When none of these three LEDs are lit the total load is below 40% of the total 48W. When the load

is above 40% you see the green LED turn on. At loads higher than 70% both the green and yellow LEDs

are lit. When you exceed the 90% of the total maximum load all three LEDs will be lit.

Global status indicator

If the DC7 operates within total maximum output power limit of 48W and everything functions normally its

the red LED inside the letter in CIOKS logo will be lit. If the power supply is globally overloaded this O

global status indicator will turn o. The operation of the DC7 is maintained and your pedals are still

powered. The show must go on, but you are just about to lose it. If the global overload is severe or the 24V

AUX outlet is short circuited the main AC/DC converter of the DC7 goes into hiccup mode and both the

CIOKS LED and all seven status LEDs will be pulsing. The power to your pedals is cut o. The DC7 in

hiccup mode will not damage your pedals.

Pedalboard mounting

Pedaltrain

For CIOKS DC7 we recommend three ways of mounting to a Pedaltrain pedalboard. The most solid way

is using the drill template to drill two diagonally positioned ø4,5 or ø5,0mm holes in the pedalboard and

fasten the DC7 to it with the two included screws. An easy alternative way is to use the GRIP bracket

where no drilling is needed. Due to the DC7 y at prole and low weight you can use Dual-’s extremel

Lock tape or industrial Velcro to fasten it below any type of Pedaltrain pedalboard.

Temple Audio

The three threaded holes in the bottom of CIOKS DC7 are aligned with the grid of the Templeboard and

allow for very easy mounting on top or below any Temple Audio pedalboard with the included 2 screws.

We recommend using the two holes positioned diagonally. If you want to make a distance between the

board’s surface and the DC7 to allow space for the Temple Audio nger screws you should get a set of

three 8mm hex stand-os with matching screws (order no. 3HEX) and then use these with all three

threaded holes in the bottom of the DC7.

Other pedalboard types

For other types of pedalboards we recommend using one of the four mounting methods described in the

Pedaltrain Temple Audio sections above or by other means using some of the ve threaded M4 holes or

and metric M4 screws. Remember not to penetrate the DC7 with more than 5mm with the screws used.

Included accessories

Flex cables

CIOKS oers a wide selection of dierent Flex cable types for connection your pedals to the power

supply. Below you see a list of the included Flex cables with your unit:

• Standard Flex type 1 black with 5,5/2,1mm centre negative DC plug x7 –

• Standard Flex type 2 red with 5,5/2,1mm centre positive DC plug –x1

• Standard Flex type 4 green with 5,5/2,5mm centre positive DC plug x1 –

• Standard Flex type 5 black with tip positive 3,5mm Jack plug –x1

• Split Flex type 1 black with two 5,5/2,1mm centre negative DC plugs –x1

• 3-way daisy chain Flex type 1 black with three 5,5/2,1mm centre negative DC plugs –x1

Split Flex should be used if you would like to power two pedals with the same voltage using only one

outlet. In the same manner you should use the 3-way daisy chain if you wish to power three pedals of one

outlet. For further information about Flex cables please have a look at the included Flex cable selection

guide or visit CIOKS web site.

Mounting hardware

We have included all the needed mounting hardware to mount the power supply on top or underneath a

Pedaltrain or a Temple Audio pedalboard. You can of course also attach it to other types of pedalboards.

Not included accessories

The GRIP

This patent pending bracket can be purchased separately and is an easy and drill-free way to mount

CIOKS DC7 below any Pedaltrain board except the smallest Nano model.

Produkt Specifikationer

Mærke:	Cioks
Kategori:	Ikke kategoriseret
Model:	DC7

Har du brug for hjælp?

Hvis du har brug for hjælp til Cioks DC7 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Cioks Manualer

Cioks DC7 Manual

24 August 2024

Cioks 4 Manual

23 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025