Cordes CC-800 Manual

Cordes Alarmsystem CC-800

Læs gratis den danske manual til Cordes CC-800 (2 sider) i kategorien Alarmsystem. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Cordes CC-800, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CC-800_alarm_vibra_manual_A4_ZW_RZ_D/E 18.06.12 08:06 Seite 1

Op de Solt 42 · D – 22391 Hamburg

SOLAR POWER

SOLAR POWER SOLAR POWER

VIBRA

VIBRAVIBRATION/MAGNET ALARM

TION/MAGNET ALARM

TION/MAGNET ALARMTION/MAGNET ALARM

MODEL: CC-800

MODEL: CC-800MODEL: CC-800 INSTRUCTION MANUAL

NOTE:

A: ‘Remove the Jumper Cap will return to factory default code

B: Do not set the new code start with 4 as 4 is the digit to arm the unit.

And the former three digits cannot be set as ‘111’ or ‘222’as these

c odes will be forbidden and turn to disarm mode

C: For security reason, if this procedure is not completed correctly

within 30 seconds, alarm will return to disarm mode

Activate/deactivate vibration function

Under disarm mode, input correct code, then input activate code ‘222’, red

LED will flash three times to confirm the vibration function is activated and

return to disarm mode.

Under disarm mode, input correct code, then input deactivate code ‘111’,

red LED will flash three times to confirm vibration function is deactivated

and return to disarm mode.

NOTE The vibration detect function is activated automatically when install:

the Jumper Cap.

Operation

When existing from the protected area

Press number ‘4’ on keypad and a confirmed tone will indicate that the

alarm is armed. You have 30 seconds to vacate the area. After this time,

if magnetic contact is broken or vibration is detected, the alarm will be

triggered.

When entering the protected area

Simply type your four digit security code (default factory code ‘1234’) within

5 seconds. This will disarm the alarm.

Please note: The Main unit has installed 1pc lithium battery which can

charge energy by the solar panel. (1).

LED (Low Battery Indicator) Status

If LED is flashing, it means the charging is saturated.

If LED keeps flashing discontinuously, it means changing the code

at present.

If LED is on, it is low battery indicator and means battery energy is low.

The battery is needed to be charged.

Care and maintenance

To clean the case, simply use a soft slightly damp cloth with water and wipe

dry immediately.

Caution: Never use chemicals to clean the case, as they may damage the

plastic and the function of product.

Product Diagram

Installation

Put the Jumper Cap into the back of the main unit firstly as showed in

picture B .

Install the main unit on the bracket as showed in picture C.

Apply the double sided adhesive tape (included) to the backside bracket

of the main unit and magnetic module. Mount to window, door or cabinet

opening, aligning main unit with the magnetic module, it can be on the left

or right hand side , the gap between main and magnetic module is less than

1 0mm.

Programming the alarm

Set PIN code

PIN code can be modified under disarm mode as below:

1. Open the back cover and install the Jumper Cap properly as

showed in picture A (6)

2. Input default code (default factory code ‘1234’), red LED flashes

3. Enter new four digits PIN code

4. Red LED light flashes three times to confirm new code is set

successfully, the unit will return to disarm mode

SPECIFICATION:

Measure main unit: 4,6cm x 4,6cm x 2,1cm

Measure magnetic contact: 1,3cm x 4,5cm x 1,2cm

W x H x T

Horn Level: 85db(A) 3m

Ambient Humidity: 10% - 90%

Weight incl. battery: 49g

Power Source: rechargeable batterie

(included)

CC-800_alarm_vibra_manual_A4_ZW_RZ_D/E 18.06.12 08:06 Seite 2

Produkt Specifikationer

Mærke:	Cordes
Kategori:	Alarmsystem
Model:	CC-800

Har du brug for hjælp?

Hvis du har brug for hjælp til Cordes CC-800 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Alarmsystem Cordes Manualer

Cordes CC-2200 Manual

27 December 2024

Cordes CC-400 Manual

21 August 2024

Cordes CC-800 Manual

21 August 2024

Alarmsystem Manualer

Nyeste Alarmsystem Manualer

Hager S262-22F Manual

9 August 2025

Hager TGA200 Manual

9 August 2025

Smartwares HA701SL-IC Manual

8 August 2025

Smartwares SC37 Manual

8 August 2025

Brennenstuhl WF 2050 Manual

4 August 2025

Blaupunkt E02 Manual

3 August 2025

Abus Terxon SX Manual

2 August 2025

Abus FO400A Manual

2 August 2025

Elro SA68M Manual

31 Juli 2025

Hikvision DS-PM2-D Manual

28 Juli 2025