Cotech AR0027 Manual

Cotech Lys AR0027

Læs gratis den danske manual til Cotech AR0027 (5 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Cotech AR0027, eller vil du spørge andre brugere om produktet?

Side 1/5
GREAT BRITAIN • CUSTOMER SERVICE
contact number: 08545 300 9799
e-mail: customerservice@clasohlson.co.uk internet: www.clasohlson.com/uk
ENGLISH
1
2
3
4
5
6 7 8 9
10
11
Ver. 20131209
ALBIN LED Wall Light
Art.no 36-4855 Model AR0027-black
Please read theentire instruction manual before using theproduct and save it for future reference.
We reserve theright for any errors in text or images and any necessary changes made to technical data.
If you have any questions regarding technical problems please contact our Customer Services.
1. Location 1. UndotheM6 bolts and take off thewall bracket (2).
Don’t mix thewashers up.
2. Markout theposition of themounting holes on
thewall using thewall bracket as atemplate.
Drillholes for themounting screws (1). Usesuitable
screws and wall plugs if necessary. Thefloodlight
must be fixed securely. Beforestarting to drill, check
that there are no hidden electrical cables or water
pipes in thewall.
3. Removethebolts holding thejunction box cover
on, remove thecable gland and thestrain relief and
thread thepower cable (3G, 0.75) into thejunction
box through thecable gland and rubber grommet.
4. Connect thethree wires: L- Live (brown), N - Neutral
(blue) and - Electrical earth (green/yellow) to
theterminal block as marked in thejunction box.
Consider thefollowing
advice:
• The most suitable
height to mount
thelight at is
1.8–2.5m above
theground.
• Ideally, thelight
should be horizontal.
2. Installation
1. Wall screws
2. Wall bracket
3. Spring washer
4. Plain washer
5. M6bolt
6. Cablegland
7. Rubber
grommet
8. Lamp housing
9. Terminal block
10. Cable strain
relief withbolts
11. Junction
box cover
(withbolts)
5. Pushtheterminal block into thejunction box and
clamp thecable in place using thestrain relief.
Thenret thejunction boxcover.
6. Boltthelamp housing to thewall bracket.
7. Tiltthelamp housing to thedesired angle and tighten
thebolts (1).
8. Replace thefuse.
3. Disposal
This product should be disposed of in accordance with
local regulations. If you are unsure how to proceed,
contact your local authority.
4. Technical data
Ideal for use with motion detectors.
Mains supply 220–240 V AC, 50Hz
Power 20 W
Light source 14×1 W LED (non-replaceable)
Bright LEDs (6,500 K), 770lm
Aperture 210×130 mm
Protection class IP44 (approved for outdoor use)
Safety class Class 1 (this light fitting must
be earthed)
Important: Readtheentire instruction manual before
installation. Theinstallation should be carried out by
aqualified electrician and conform to current regulations.
Warning: Makesure that thepower is turned off and that
thefuse is removed before beginning any installation,
change of light bulb or service.


Produkt Specifikationer

Mærke: Cotech
Kategori: Lys
Model: AR0027

Har du brug for hjælp?

Hvis du har brug for hjælp til Cotech AR0027 stil et spørgsmål nedenfor, og andre brugere vil svare dig