Crestron CBLR2-CAT5E Manual

Crestron Ikke kategoriseret CBLR2-CAT5E

Læs gratis den danske manual til Crestron CBLR2-CAT5E (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Crestron CBLR2-CAT5E, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
DO GUIDE
CBLR2 Series
Cable Retractors for FlipTops
TM
DO Prepare the FlipTop
Preparation of the Crestron
®
FlipTop™ consists of the following:
• Modifying the FlipTop assembly to accommodate the cable retractors
• Determining the desired mounting orientation (Retractors are shipped congured for vertical
orientation, but are easily recongured for horizontal orientation.)
NOTE: The CBLR2-DP-V and CBLR2-DP-H models are dedicated to vertical and horizontal
orientation, respectively.
NOTE: For preparation of the FlipTop 600 Series models, refer to “Modify the FlipTop (FlipTop 600
Series Models).”
Modify the FlipTop (Excludes FlipTop 600 Series Models)
1. Remove four screws (A) to detach the lower bar assembly. Also remove two screws (B). Retain
screws A and B to attach the FlipTop mounting bracket assembly. Refer to the FlipTop mounting
brackets table provided in the “DO Check the Accessories” section on the next page to ensure
that the mounting bracket received is appropriate for the FlipTop being modied.
2. Remove four screws (C) to detach the cable guide. Retain the screws to attach the two side ller
plates (sold separately).
3. Move the mounting bracket assembly up into position and secure it using four screws (A) and two
screws (B) removed in step 1.
4. Position the side ller plates and secure them using four screws (C).
Modify the FlipTop (FlipTop 600 Series Models)
Retractors can be installed in both the left and right sides of the FlipTop 600 Series models.
1. Remove the screw (C) holding the cable guide in place, and then remove the cable guide.
2. Remove the screws (D) holding the cable pass-through bracket in place, and then remove the
cable pass-through bracket.
3. Remove the shoulder screws from the front of the unit. Save these as they are used in retractor
installation.
Recongure the Retractors for Horizontal Operation
NOTE: The CBLR2-DP-V and CBLR2-DP-H models are dedicated to vertical and horizontal
orientation, respectively.
To recongure the retractors for horizontal orientation, refer to the following illustrations and perform
these steps:
1. Remove the four screws (E), two from each side of the retractor, that attach the neck in the vertical
orientation.
2. Reposition the neck as shown in the horizontal orientation view and attach it using the four screws
(E) to secure the neck in that position.
DO Adjust the Retractor
Once the retractor arm conguration is set, refer to the following illustration and adjust the retractor
arm tension and cable retraction speed as follows:
1. Adjust the retractor tension by loosening the top thumb screw enough to enable pulling or pushing
of the adjacent cable end. Align the red screw with the label arrow.
2. Adjust the cable retraction speed.
a. Pull the knob outward and move it to the VERT or HORZ position to match the conguration
of the retractor arms.
b. Pull the cable (plug end) out so it is fully extended.
c. Pull the cable a second time to cause it to retract, and observe the speed of the cable
retraction. If it is too slow or too fast, reposition the knob to an intermediate position and
recheck.
Mounting
Bracket
Assembly
Side Filler Plates
(4) Screws (E)
(Two on Each Side)
Side View
Retractor Neck
(4) Screws (E)
(Two on Each Side)
Side View
Retractor Neck
Thumb Screw
Cable End
HORZ
VERT
Knob
Red Screw
Once installed, use the top thumb screw
to adjust the cable length until the red
screw is aligned with the arrow.
Cable Retraction
Speed Adjustment
Slow
Fast
Mounting
Bracket
Assembly
Screws (A)
Screw (B)
Screw (B)
Screws (C)
Side Filler
Plates
Cable Guide
Cable Pass-Through Bracket
Shoulder Screws
Screws (C)
Screws (D)
Lower Bar
Assembly
Cable
Guide
Screws (A)
Screw (B)
Screw (B)
Screws (C)

Produkt Specifikationer

Mærke: Crestron
Kategori: Ikke kategoriseret
Model: CBLR2-CAT5E
Type: Kabelindtrækker
Antal pr. pakke: 1 stk
Produktfarve: Sort
Formål: Skrivebord

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CBLR2-CAT5E stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Crestron Manualer

Crestron

Crestron HZ2-BTNS-5 Manual

7 Oktober 2025
Crestron

Crestron HZ2-AUX Manual

7 Oktober 2025
Crestron

Crestron PW-2407WUL Manual

29 September 2025
Crestron

Crestron C2N-UNI8IO Manual

28 September 2025
Crestron

Crestron CLXI-4HSW4 Manual

24 September 2025
Crestron

Crestron GLD-LED-50W Manual

24 September 2025
Crestron

Crestron TPS-4LW Manual

23 September 2025
Crestron

Crestron Zūm Manual

23 September 2025
Crestron

Crestron SIMPL Manual

23 September 2025
Crestron

Crestron UC-FCM-T Manual

23 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MuxLab

MuxLab 500439 Manual

5 November 2025
GVM

GVM BL160-II Manual

5 November 2025
Uniprodo

Uniprodo UNI_ROLL_03 2in1 Manual

5 November 2025
Rockville

Rockville SS6 Manual

5 November 2025
Silk'n

Silk'n VacuPedi FTC04 Manual

5 November 2025
MEPROLIGHT

MEPROLIGHT MCO PRO Manual

5 November 2025
XPG

XPG Battlecruiser II Manual

5 November 2025
Hosa

Hosa USQ-110 Manual

5 November 2025
JMAZ

JMAZ Centipede Quadro Manual

5 November 2025
Lake People

Lake People Mic-Amp F311-D Manual

5 November 2025