Crestron CLX-4HSW4 Manual

Crestron Ikke kategoriseret CLX-4HSW4

Læs gratis den danske manual til Crestron CLX-4HSW4 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Crestron CLX-4HSW4, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
CLT- & CLX-4HSW4
Functional Summary NOTE: Modules and terminal blocks must be installed
into the lowest available spaces and continue toward the
top of the enclosure.
The Crestron 4-Feed, 4-High Switch Terminal Block and
Module (CLT-4HSW4 and CLX-4HSW4, respectively),
are considered a single entity and must be used together.
They ship separately to permit termination of the field
wiring to the CLT-4HSW4 prior to installation of the
CLX-4HSW4, as described in this guide. They can be
mounted in any Crestron Automation Enclosure (CAEN-
Series Enclosures). The terminal block is designed to
terminate four circuit feeds (LINE and NEUTRAL) and
distribute the controlled circuits (LOAD) to the fixtures.
The module connects to the terminal block and performs
switching (non-dim) control of four incandescent, low
voltage, neon, cold cathode, fluorescent, or HID lighting
loads, or motor loads. The maximum load is 16 amps (1/2
HP) for each controlled circuit (64 amps total per
module). The unit requires 120VAC 60 Hz input voltage.
An oversize heat sink dissipates heat efficiently. There are
LEDs on the module to indicate communication to a
Cresnet network, input power to the module, and output
power to the load.
Terminal Block & Module Locations (Single-wide Enclosure)
MODULETERMINAL
BLOCK
GROUNDING
TERMINAL
BLOCK
Industry Compliance
This product is Listed to applicable UL Standards and
requirements by Underwriters Laboratories Inc.
Terminal Block & Module Locations (Double-wide Enclosure)
(E103692)
GROUNDING TERMINAL BLOCKS
MODULETERMINAL BLOCK
(LEFT)
TERMINAL BLOCK
(RIGHT)
Installation
Terminal block and module must be mounted into a
Crestron Automation Enclosure by a licensed electrician,
in accordance with all national and local codes.
CAUTION: This equipment is for indoor use only and
needs to be air-cooled. Mount in a well-ventilated area.
The ambient temperature must be 32°F to 104°F (0°C to
40°C). The relative humidity must be 0% to 90% (non-
condensing).
Terminal blocks are installed along the left side of single-
wide enclosures and along the outside edges (left and
right sides) of double-wide enclosures. Modules are
installed along the right side of single-wide enclosures
and side-by-side in the center of double-wide enclosures.
When installing modules and terminal blocks in a double-
wide enclosure, be sure to invert units on the right side so
that they can be properly wired. Refer to the illustrations
shown in the next column when considering the location
of terminal blocks and modules within an enclosure.
Crestron Electronics, Inc. Installation Guide – DOC. 5986C
15 Volvo Drive Rockleigh, NJ 07647 (2002068)
Tel: 888.CRESTRON 11.06
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Terminal Block & Module Crestron CLT- & CLX-4HSW4
5. Grounding terminal blocks are available in the
cabinet for termination of ground wires. Tighten
to 35 in-lbs. (14 – 10 AWG), 40 in-lbs.
(8 AWG), or 45 in-lbs. (6 – 4 AWG).
NOTE: Unless otherwise indicated, the lighting system
specified in this guide is modular, requiring assembly in
the field by a licensed electrician, in accordance with all
national and local codes.
6. Test each circuit for electrical faults by turning
on each of the circuit breakers, checking that the
breakers do not trip, and that power is delivered
to the proper loads.
If you require an assembled UL Listed panel, Crestron
offers this service through its UL Listed panel shop. This
includes complete in factory system configuration and
assembly by Crestron for an additional fee.
Wiring Diagram of the Terminal Block to the Feed and
Load(s)(Single-wide and Left Side Double-wide Enclosures)
Terminal Block Installation and Field
Wiring
TO
LOAD
4
TO
LOAD
3
TO
LOAD
2
TO
LOAD
1
LINE 1 (*)
LINE 2 (*)
LINE 3 (*)
LINE 4 (*)
NEUTRAL
NEUTRAL
NEUTRAL
NEUTRAL
GROUNDING
TERMINAL
BLOCK
GND
TERMINAL
BLOCK
LEFT
SIDE
WIRING
LABEL
AREA FOR
MODULE
LOCATION
LABEL
BYPASS
JUMPERS
(*) FROM 15 OR 20 AMP
CIRCUIT BREAKER
NOTE: Both left-side and right-side adhesive wiring
labels are provided. The left-side labels are used in both
single and double-wide enclosures. The right-side labels
are only used in double-wide enclosures.
1. Remove the backing from the left or right
adhesive wiring label.
2. Apply the adhesive label by aligning the holes in
the label with the holes on the Crestron
Automation Enclosure where the terminal block
is to be mounted. The wiring label lies beneath
the terminal block as shown in the two wiring
diagrams on this page.
3. Use the two supplied self-tapping pan Phillips
screws (8B x ¼ length) to secure the terminal
block to the Crestron Automation Enclosure.
CAUTION: Bypass jumpers are provided to allow
testing of circuits and to protect the module during
installation. When properly secured by two screws,
each of the four jumpers on the black and red
sections of the terminal block shorts the LINE in to
SWITCH out so that the circuit is energized. Do not
remove any bypass jumpers until all feed and load
wiring has been completed, the circuit has been tested
for electrical faults, and the module has been
installed. Refer to “Module Installation” on next
page.
Furthermore, the four jumpers on the white sections
of the terminal block tie the neutral ins to the neutral
outs. These jumpers should never be removed.
Wiring Diagram of the Terminal Block to the Feed and
Load(s) (Right Side Double-wide Enclosures)
TO
LOAD
1
TO
LOAD
2
TO
LOAD
3
TO
LOAD
4
LINE 1 (*)
LINE 2 (*)
LINE 3 (*)
LINE 4 (*)
NEUTRAL
NEUTRAL
NEUTRAL
NEUTRAL
GRO UNDING
TERMINAL
BLOCK
GND
TERMINAL
BLOCK
RIGHT
SIDE
WIRING
LABEL
AREA FOR
MODULE
LOCATION
LABEL
BYPASS
JUMPERS
(*) FROM 15 OR 20 AMP
CIRCUIT BREAKER
NOTE: Use copper conductors only – rated 75°C
4. With the circuit breaker turned off, connect the
circuit feed (LINE and NEUTRAL) and
controlled circuit (LOAD) wires to the terminal
block per the markings provided on the wiring
label (as shown in the diagrams on this page).
Terminal blocks accept one 14 - 10 AWG wire.
Wires should be stripped to ½ inch. Tighten
terminal blocks to 9 in-lbs.
2 •
•
•
•• Terminal Block & Module: CLT- & CLX-4HSW4 Installation Guide – DOC. 5986C

Produkt Specifikationer

Mærke: Crestron
Kategori: Ikke kategoriseret
Model: CLX-4HSW4

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CLX-4HSW4 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Crestron Manualer

Crestron

Crestron FT2-700-ELEC-PTL Manual

30 Juli 2025
Crestron

Crestron RMK-AMP-X Manual

30 Juli 2025
Crestron

Crestron DIN-GWDL-SPLTR Manual

30 Juli 2025
Crestron

Crestron HD-CTL-101 Manual

30 Juli 2025
Crestron

Crestron FT2-202-ELEC-PTL Manual

30 Juli 2025
Crestron

Crestron STIRP Manual

30 Juli 2025
Crestron

Crestron CSP-LIR-USB Manual

30 Juli 2025
Crestron

Crestron CEN-IO-COM-202 Manual

30 Juli 2025
Crestron

Crestron CEN-IO-DIGIN-204 Manual

29 Juli 2025
Crestron

Crestron DIN-DLI Manual

29 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman MY500XT Manual

1 August 2025
Navman

Navman FOCUS150 GPS Manual

1 August 2025
Scheppach

Scheppach TW1000 Manual

1 August 2025
Navman

Navman MiVue 750 WIFI Manual

1 August 2025
Navman

Navman MiVue Drive FHD Manual

1 August 2025
Midea

Midea MEC64 Manual

1 August 2025
Navman

Navman MY50T Manual

1 August 2025
Navman

Navman M100 Manual

1 August 2025
Navman

Navman MiVue 770 SAFETY Manual

1 August 2025
Navman

Navman MiVue 790 Manual

1 August 2025