Crestron CLXI-1DELV4 Manual

Crestron Ikke kategoriseret CLXI-1DELV4

Læs gratis den danske manual til Crestron CLXI-1DELV4 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Crestron CLXI-1DELV4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

CLTI- & CLXI-1DELV4

Crestron Electronics, Inc. Installation Guide – DOC. 6405A

15 Volvo Drive Rockleigh, NJ 07647 (20138 )15

Tel: 888.CRESTRON 03.08

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Functional Summary

The Crestron 1-Feed, 4-Dimmer Electronic Low Voltage

Terminal Block and Module (CLTI-1DELV4 and

CLXI-1DELV4, respectively), are considered a single

entity and must be used together. They ship separately to

permit termination of the field wiring to the

CLTI-1DELV4 prior to installation of the

CLXI-1DELV4, as described in this guide. They can be

mounted in any Crestron Automation Enclosure (CAEN

or CAENIB-Series Enclosures). The terminal block is

designed to terminate the circuit feed (LINE and

NEUTRAL) and distribute the controlled circuit (LOAD)

to the fixture(s). The module connects to the terminal

block and performs dimming control of four electronic

low-voltage or incandescent loads. The maximum load is

10 amps for any controlled circuit, limited to 13 amps

total per module. The unit requires 230VAC 50 Hz, 1

phase input voltage. An oversize heat sink dissipates heat

efficiently. There are LEDs on the module to indicate

communication to a Cresnet network, input power to the

module, and output power to the load.

NOTE: When connecting to an Arc Fault Breaker, the

load should not exceed 1000 watts.

Installation

Terminal block and module must be mounted into a

Crestron Automation Enclosure by a licensed electrician,

in accordance with all national and local codes.

CAUTION: This equipment is for indoor use only and

needs to be air-cooled. Mount in a well-ventilated area.

The ambient temperature must be 0°C to 40°C (32°F to

104°F). The relative humidity must be 0% to 90% (non-

condensing).

Terminal blocks are installed along the left side of single-

wide enclosures and along the outside edges (left and

right sides) of double-wide enclosures. Modules are

installed along the right side of single-wide enclosures

and side-by-side in the center of double-wide enclosures.

When installing modules and terminal blocks in a double-

wide enclosure, be sure to invert units on the right side so

that they can be properly wired. Refer to the illustrations

shown in the next column when considering the location

of terminal blocks and modules within an enclosure.

NOTE: Modules and terminal blocks must be installed

into the lowest available spaces and continue toward the

top of the enclosure.

Terminal Block & Module Locations (Single-wide Enclosure)

GROUNDING

TERMINAL

BLOCK

TERMINAL

BLOCK

MODULE

(INSTALL INTO

LOWEST AVAILABLE

SPACES)

Terminal Block & Module Locations (Double-wide Enclosure)

TERMINAL BLOCK

(RIGHT)

GROUNDING TERMINAL BLOCKS

TERMINAL BLOCK

(LEFT)

MODULE

(INSTALL INTO

LOWEST AVAILABLE

SPACES)

Terminal Block & Module Crestron CLTI- & CLXI-1DELV4

2 •

•

•• Terminal Block & Module: CLTI- & CLXI-1DELV4 Installation Guide – DOC. 6405A

Terminal Block Installation and Field

Wiring

NOTE: To install a CLTIBN Circuit Breaker Terminal

Block, refer to the latest version of the CLTIBN

Installation Guide (Doc. 6561) which can be downloaded

from the Crestron website (www.crestron.com/manuals).

NOTE: Both left-side and right-side adhesive wiring

labels are provided. The left-side labels are used in both

single and double-wide enclosures. The right-side labels

are only used in double-wide enclosures.

1. Remove the backing from the left or right

adhesive wiring label.

2. Apply the adhesive label by aligning the holes in

the label with the appropriate holes on the

Crestron Automation Enclosure where the

terminal block is to be mounted. For information

on mounting locations, refer to the latest version

of the CAEN Installation Guide (Doc. 5940) or

the CAENIB Installation Guide (Doc. 6562). The

wiring label lies beneath the terminal block as

shown in the two wiring diagrams on this page.

3. Use the two supplied self-tapping pan Phillips

screws (8B x ¼ (6 mm) length) to secure the

terminal block to the Crestron Automation

Enclosure.

CAUTION: Bypass jumpers are provided to allow

testing and to protect the module during installation.

When properly secured by five screws, the bypass

jumper on the brown and red section of the terminal

block shorts the LINE in to DIM out so that the

circuit is energized. Do not remove this bypass

jumper until all feed and load wiring has been

completed, the circuit has been tested for electrical

faults, and the module has been installed. Refer to

“Module Installation” on next page.

Furthermore, the jumper on the blue section of the

terminal block ties the neutral in to the neutral outs.

This jumper should never be removed.

NOTE: Use copper conductors only – rated 75°C.

4. With the circuit breakers turned off, connect the

circuit feed (LINE and NEUTRAL) and

controlled circuit (LOAD) wires to the terminal

block per the markings provided on the wiring

label (as shown in the diagrams on this page).

Terminal blocks accept one 0.2 - 4 mm

2 wire.

Wires should be stripped to 12 mm. Tighten

terminal blocks to 1 Nm.

5. Grounding terminal blocks are available in the

cabinet for termination of ground wires. Tighten

2.5-6 mm2 wires to 4 Nm, 10 mm2 wires to 4.5

Nm, or 16 mm2 wires to 5.1 Nm.

6. Test the circuit for electrical faults by turning on

the circuit breakers, checking that the breakers

do not trip, and that power is delivered to the

proper loads.

NOTE: If installing in a CAENIB, complete the

installation with a CAENIB-BP Blank Plate. Refer to the

latest version of the CAENIB-BP Installation Guide (Doc.

6563) for details.

Wiring Diagram of the Terminal Block to the Feed and

Load(s) (Single-wide and Left Side Double-wide Enclosures)

TERMINAL

BLOCK

GROUNDING

TERMINAL

BLOCK

GND

LEFT SIDE

WIRING LABEL

LOAD(S)

AREA FOR

MODULE

LOCATION

LABEL

(FROM 16 AMP OR SMALLER

CIRCUIT BREAKER)

NEUTRAL

LINE

BYPASS

JUMPER

Wiring Diagram of the Terminal Block to the Feed and

Load(s) (Right Side Double-wide Enclosures)

NEUTRAL

(FROM 16 AMP

OR SMALLER CIRCUIT

BREAKER)

TERMINAL

BLOCK

AREA FOR

MODULE

LOCATION

LABEL

RIGHT SIDE

WIRING LABEL

LOAD(S)

GROUNDING

TERMINAL

BLOCK

LINE

BYPASS

JUMPER

GND

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	CLXI-1DELV4

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CLXI-1DELV4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron Green Light GL-EXP-SW-CN Manual

10 September 2025

Crestron FT2A-PWR-IT-1-BASIC Manual

10 September 2025

Crestron FT2A-PWR-AU-2 Manual

10 September 2025

Crestron FT2A-PWR-UK-2 Manual

10 September 2025

Crestron Green Light GLXX-2DIM8 Manual

10 September 2025

Crestron FT2A-PWR-EU-1-BASIC Manual

10 September 2025

Crestron FT2A-PWR-UN-1-BASIC Manual

9 September 2025

Crestron FT2A-PWR-US-3 Manual

9 September 2025

Crestron FT2A-PWR-SW-1-BASIC Manual

9 September 2025

Crestron FT2A-PWR-US-1-BASIC Manual

9 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock PT44 Manual

14 September 2025

BSS Audio FDS-366T Manual

14 September 2025

Systemair Airline R-114 Manual

14 September 2025

IFM SU2031 Manual

14 September 2025

Morel Tempo Ultra Integra 502 Manual

14 September 2025

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025