Crestron DM-RMC-4K-SCALER-C Manual

Crestron Ikke kategoriseret DM-RMC-4K-SCALER-C

Læs gratis den danske manual til Crestron DM-RMC-4K-SCALER-C (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 51 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 26 anmeldelser. Har du et spørgsmål om Crestron DM-RMC-4K-SCALER-C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DO GUIDE

DO Connect the Device

Connect the device as required for the application.

Connections, Left Side

Connections, Right Side

NOTE: The DM IN port is a PoDM+ powered device (PD) port and is also compatible with HDBaseT

PoE+.

In order for the device to receive PoDM+, the device requires connection to a DigitalMedia™

switcher or other equipment that has a PoDM+ power sourcing equipment (PSE) port. In order

for the device to receive HDBaseT PoE+, the device requires connection to equipment that has a

corresponding HDBaseT PoE+ PSE port. Any wiring that is connected to a PoDM+ or HDBaseT PoE+

PSE port is for intrabuilding use only and should not be connected to a line that runs outside of the

building in which the PSE is located.

Connection to the included power pack is not required when PoDM+ or HDBaseT PoE+ is used to

power the device.

NOTE: Connection of the CEN-SWPOE-16 to the POE IN ports of DMC-4K-CO-HD output cards in a

DigitalMedia switcher can provide PoDM+ power to up to seven DM-RMC-4K-SCALER-C devices.

NOTE: The LAN port can connect to an Ethernet switch only if the DM IN port does not connect to a

DigitalMedia switcher.

DM-RMC-4K-SCALER-C/DM-RMC-4K-SCALER-C-DSP

4K DigitalMedia 8G+

Receiver and Room Controller with Scaler

DO Install the Device

The Crestron

DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP can be mounted onto a

at surface or onto a rack rail.

Mounting onto a Flat Surface

Using four mounting screws (not included), mount the device onto a at surface such as a wall or a

ceiling.

Mounting onto a Wall

Mounting onto a Rack Rail

The DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP mount onto the front or rear rail of a

rack. Position either the left or the right mounting ange of the device so that the holes align with the

holes in the rack. Then, secure the device to the rack using two rack mounting screws (not included).

Mounting onto a Rack Rail

DO Check the Box

QTY PRODUCT PART NUM.

2 Connector, 4-Pin 2003576

2 Connector, 5-Pin 2003577

1 Power Pack, 24 Vdc 1.25 A, 100-240 Vac 2045870

COM:

To RS-232

device

IR 1–2:

To IR

controllable

devices

AUDIO OUT:

To balanced/

unbalanced

stereo line level

audio output

device

RELAY 1–2:

To relay

controllable

devices

Ground

LAN:

10BASE-T/

100BASE-TX

Ethernet to local

network device

DM IN:

From

switcher,

transmitter, or other

DM device or from

HDBaseT

device

24 V:

1.25A MAX:

From

included

power pack

HDMI OUT:

To HDMI

display

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	DM-RMC-4K-SCALER-C
Bredde:	137 mm
Dybde:	28 mm
Højde:	318 mm
Vægt:	625 g
Produktfarve:	Sort
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
HDCP:	Ja
Strømforbrug (typisk):	18 W
Driftstemperatur (T-T):	0 - 40 °C
Husmateriale:	Metal
Indgangsspænding for vekselstrømsadapter:	100-240 V
Frekvens for vekselstrømsadapter:	50/60 Hz
LED-indikatorer:	Ja
Signal/støjforhold:	95 dB
Antal HDMI-udgange:	1
Varmeafgivelse:	63 BUT/t
Skalerede opløsninger:	1920 x 1080,2560 x 1600,3840 x 2160,4096 x 2160
Antal RJ-45-porte:	2
Baud hastighed:	115200 Bd
Maksimal pixel ur:	300 MHz
Kanalseparation (1kHz):	90 dB