Crestron Excite IW8 Manual

Crestron Højttaler Excite IW8

Læs gratis den danske manual til Crestron Excite IW8 (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Crestron Excite IW8, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Excite™ In-Wall Speakers

quickstart guide

IW5, IW6, IW8

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

IW5, IW6, IW8

Mount/Remove Speakers

The in-wall speakers include six toggle clamps that simplify

the mounting process. If grilles are mounted on the speak-

ers, remove them before proceeding. (Refer to “Install/

Remove Grilles”, below.)

1. Connect the speaker cable wires to the spring terminals

by pressing the top of the terminals down and inserting

the exposed strands into the hole. Make sure that left

and right channels are connected to the left and right

speakers, respectively, and that the wires go to the + +

(red coded) terminals, and the wires go to the – –

(black coded) terminals.

2. With the toggle clamps turned inward, insert the

speaker into the opening. As you tighten the six screws

on the front of the speaker, the toggle clamps will first

rotate into clamping position and then begin holding the

speaker to the wall. Tighten the screws until the

speaker is secure; do not overtighten.

3. Speaker removal is accomplished by reversing the

procedures given in steps 1 and 2 above.

a. Loosen the front screws to unclamp the speaker.

Continue to loosen the screws until the toggle

clamps rotate inward.

b. When the speaker is loose, carefully pull the

speaker out from the opening.

c. Disconnect the wires from the terminals.

Install/Remove Grilles

To install the grille, place it in position and carefully press

until the surface of the grille is flush with the surface of the

outer flange.

To remove the grille, insert a slim, flat-blade screwdriver

between the grille and the outer flange, and carefully pry

the grille up and out.

It may be necessary to press one or more of the mounting

screws and toggle clamps toward the front to push the grille

free of the flange.

1Installation

For Regulatory Compliance information, refer to the latest

version of Doc. 7148.

Ideal components of every Sonnex™, Prodigy®, or

Adagio® multiroom audio system, Excite™ speakers

by Crestron® offer excellent sound quality and

flexible installation in a range of popular sizes and

configurations.

QUICKSTART DOC. 7128B (2029451) 05.11

The IW5, IW6, and IW8 rectangular in-wall speakers,

sold in pairs, include paint plugs installed on the front

of the speakers, perforated metal grilles, and a

mounting cut out template. The matte white ABS

plastic frame and white metal grille can be painted

to suit any room decor.

Determine Placement In Room

For applications such as classrooms, conference rooms, and multi-room

audio distribution installation, the Excite in-wall speakers are available in

three different sizes providing a great deal of flexibility to suit almost any

application.

For home theater applications, the Excite in-wall speaker line is an excellent

choice for the front, surround, and back channels.

As indicated in the figure below, suggested placement is at the angles from

the 0° primary viewing/ listening angle. For best results, place speakers

anywhere from the listener’s ear level to 2 to 3 feet (~ 0.6 to 0.9 meters)

above. 45°

90°

Prepare Mounting Holes

Before finalizing the speaker locations, check to

make sure there are no fixtures, pipes, air ducts,

power cables or other wiring, or other possible

obstructions. Use a good quality stud finder to

locate wall framing.

If you are not certain that there are no obstructions

in the proposed speaker locations, carefully drill a

small hole just through the wall near the middle of

the location(s) and use one of the commercially

available inspection devices designed for this

purpose, or do one of the following:

● Use a piece of stiff wire, bent into an “L”

shape, with one end long enough to explore

an area equal to the size of the speaker with

the toggle clamps extended. Insert the wire

into the hole, make sure it moves freely

through the proposed speaker area and that

there is sufficient depth, or

● Use a drywall saw to cut a small hole at a 45°

angle toward the inside of the hole. An angle

cut simplifies repair since the removed piece

can be reinserted to help plug the hole.

If there are no obstructions, use the supplied

template to trace outlines of the mounting holes on

the wall. Cut the final mounting holes at a 90°

angle to the wall.

Paint the Speakers/Grilles

Speaker rim and/or grille painting should be done

prior to mounting.

1. Leave the painting plug installed in the front of

the speaker.

2. Carefully remove the material on the underside

of the grille and set it aside for reinstallation. It

may be necessary to use a knife or other sharp

instrument to free an edge of the material so it

can be peeled away. Use care to avoid cutting

the material.

3. Dry brush or lightly spray the surface to be

painted. Use care to avoid clogging the holes

in the grille.

Rear View (Typical)

Spring

Terminals

Toggle

Clamps (6)

Front View (Typical)

Tighten

Screws

Install Cables

Run the cables from the audio source to each speaker

location following all appropriate local codes. Strip the

ends of the speaker cable wires 1/4” to 1/2” (6 mm to

12 mm) and twist the exposed strands.

0°

Left

Surround

Left

Back

Right

Back

Right

Surround

110°

135°

90°

150°

135°

150°

110°

90°

Left

Front

Right

Front

22°

30°

22°

30°

Excite™ In-Wall Speakers

quickstart guide

IW5, IW6, IW8

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

IW5, IW6, IW8

Crestron, the Crestron logo, Adagio, Excite, Prodigy and Sonnex are trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and other countries. Other trademarks, registered trademarks,

and trade names may be used in this document to refer to either the entities claiming the marks and names

or their products. Crestron disclaims proprietary interest in the marks and names of others.

The recommended setting for the low frequency

range (LF) switch is – to reduce bass when the

speaker is in a corner, + to increase bass when the

speaker is not near a wall or ceiling corner, and 0

(neutral) when the speaker is near one wall or

ceiling corner

3Specifications

QUICKSTART DOC. 7128B (2029451) 05.11

SPECIFICATION

Woofer

Size

Material

Tweeter

Size

Material

Surround Material

Environmental

Temperature

Humidity

Dimensions

Overall Height

Overall Width

Opening Height

Opening Width

Installed Depth

10.99 in (279 mm)

8.47 in (215 mm)

9.69 in (246 mm)

7.17 in (182 mm)

3.62 in (92 mm)

IW5, IW6, IW8 Specifications

Weight

For Regulatory Compliance information, refer to the latest

version of Doc. 7148.

Minimum Performance

Frequency Response (-3dB)

Power Handling (Program)

Sensitivity (1W @ 1m)

Electrical

Bass Switch

Tweeter Switch

Impedance / Voltage

Crossover Type

Terminations

Mechanical

Baffle Material

Mounting System

Grill Material

Swivel Tweeter

Paint Mask

Basket Material

Maximum Depth

Available Colors

5.25 in (134 mm)

Polypropylene

0.79 in (20 mm)

Treated cloth

Rubber

6.50 in (165 mm)

Polypropylene

0.79 in (20 mm)

Treated cloth

Rubber

8.00 in (203 mm)

Polypropylene

0.98 in (25 mm)

Treated cloth

Rubber

60 Hz - 20 kHz

60 W

87 dB

55 Hz - 20 kHz

75 W

89 dB

50 Hz - 20 kHz

125 W

89 dB

Yes

8 Ohm

2nd Order L-R

Spring Terminals

Yes

8 Ohm

2nd Order L-R

Spring Terminals

Yes

8 Ohm

2nd Order L-R

Spring Terminals

ABS

Toggle Clamps

Aluminum

Yes

Yes X2

Steel

3.93 in (100 mm)

White

ABS

Toggle Clamps

Aluminum

Yes

Yes X2

Steel

4.19 in (106 mm)

White

ABS

Toggle Clamps

Aluminum

Yes

Yes X2

Steel

4.42 in (112 mm)

White

IW5 IW6 IW8

12.43 in (316 mm)

9.54 in (242 mm)

11.13 in (282 mm)

8.24 in (242 mm)

3.88 in (99 mm)

14.47 in (368 mm)

11.02 in (280 mm)

13.17 in (335 mm)

11.02 in (280 mm)

4.11 in (105 mm)

The following table provides corrective action for possible trouble

situations. If further assistance is required, please contact a

Crestron customer service representative.

Further Inquiries

If you cannot locate specific information or have questions

after reviewing this guide, please take advantage of

Crestron's award winning customer service team by calling

Crestron at 1-888-CRESTRON [1-888-273-7876]. For

assistance in your region, please refer to the Crestron Web

site (www.crestron.com) for a listing of Crestron worldwide

offices.

You can also log onto the online help section of the Crestron

Web site (www.crestron.com/onlinehelp) to ask questions

about Crestron products. First-time users will need to establish

a user account to fully benefit from all available features.

Future Updates

Check the Crestron website periodically for manual update

availability and its relevance. Updates are identified as an

“Addendum” in the Download column.

TROUBLE

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

No sound or

intermittent

sound from

speakers.

Cable connection

error.

Verify cable connections

between amplifier and

speakers.

Amplifier not receiving

input signal or amplifier

malfunction.

Verify amplifer is functioning

correctly, that it is receiving

an input signal and that

correct input source is

selected.

Faulty device in system. Verify all devices in system

are functioning properly.

Constant

noise such

as buzz,

hum, or hiss. System grounding fault. Verify system grounding.

Poor low

frequency

output.

Incorrect polarity

connection at speaker.

Verify speaker connection

polarity (i.e. + on speaker to

+ on amplifier).

4Problem Solving

Troubleshooting

41° to 104° F (5° to 40° C)

10 to 90% RH (non-condensing, indoor use only)

3.4 lbs (1.5 kg) 4.1 lbs (1.8 kg) 5.0 lbs (2.3 kg)

2Adjustments

Opening

Width

Installed

Depth

Frequency Settings

Aiming the Tweeter

- 0 +

Front, Side, and Bottom Views (Typical)

Adjusting the high and low frequency range switch

settings (refer to illustration below) is largely a

matter of personal preference.

The settings produce the following results.

–: Reduces the selected range loudness

0: Loudness remains neutral

+: Increases the selected range loudness

The tweeter can be aimed toward the primary

listening position by gently pressing on the plastic

ring around the tweeter dome. (Refer to the

illustration above.)

Press

- 0 +

Overall

Height

Opening

Height

Overall

Width

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Højttaler
Model:	Excite IW8

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron Excite IW8 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Crestron Manualer

Crestron SAROS ICE4T Manual

7 April 2025

Crestron SAROS ICI6T Manual

7 April 2025

Crestron SAROS IC8T Manual

7 April 2025

Crestron ULTIMATE IC3-SA-WOOFER Manual

28 August 2024

Crestron ULTIMATE IC3-AW-SA-BOX-WOOFER Manual

28 August 2024

Crestron ULTIMATE IC3-AW-SA-TWEETER Manual

28 August 2024

Crestron ULTIMATE IWS82-AW-W-T-EACH Manual

26 August 2024

Crestron ULTIMATE IWLCR62-W-T-EACH Manual

26 August 2024

Crestron ULTIMATE ICS8-AW-W-T-EACH Manual

25 August 2024

Crestron SAROS ICT5T-22 Manual

25 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Hertz Cento CPK 690 Manual

13 September 2025

Adam T7V Manual

12 September 2025

Klipsch Flexus SURR 100 Manual

12 September 2025

Klipsch Detroit Manual

12 September 2025

Adam A3X Manual

12 September 2025

Adam A7X Manual

12 September 2025

Focal 1000 IW6 Manual

12 September 2025

QSC SC-423C Manual

11 September 2025

QSC AcousticDesign AD-S282H Manual

11 September 2025

Monitor Audio Bronze 200 AV 5.1.2 Manual

11 September 2025