Crestron SAROS ICE4T Manual

Crestron Højttaler SAROS ICE4T

Læs gratis den danske manual til Crestron SAROS ICE4T (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Crestron SAROS ICE4T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Saros

Express 2-Way In-Ceiling Speakers

quickstart guide

SAROS_ICE4T/ICE6T/ICE8T

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

SAROS_ICE4T/ICE6T/ICE8T

Set the Transformer Tap Selector Switch

The speakers are equipped with a 70/100 V matching transformer for distributed audio

systems. The transformer tap selector switch on the front panel is used to set the speaker

power level. Use a flat blade screwdriver to adjust the switch.

1. For SAROS_ICE4T and SAROS_ICE6T 70 V systems, use the left side settings and

select from 3.75, 7.5, 15, or watts. 30

2. For SAROS_ICE4T and SAROS_ICE6T 100 V systems, use the right side settings

and select from position should not be used.7.5, 15, or 30 watts. The X

3. For SAROS_ICE8T 70 V systems, use the left side settings and select from 7.5, 15,

30, or 60 watts.

4. For SAROS_ICE8T 100 V systems, use the right side settings and select from 15 30, ,

or 60 watts. The X position should not be used.

The switch may also be set to operation, bypassing the transformer completely. This 8Ω

setting should be used only for 8 Ω audio systems.

QUICKSTART DOC. 7496A (2037419) 11.13

Installation

Saros

Express speakers by Crestron

deliver easy

installation and excellent performance in a range of

popular sizes for cost-sensitive commercial applications.

Ideal for use in background music, paging, and sound

reinforcement systems, Saros Express speakers are

engineered to achieve full, even coverage and clear

sound quality at a very affordable cost. Their zero-

bezel frameless grille achieves an unobtrusive and

contemporary appearance. Installing the grille requires

no hardware or tools, utilizing powerful magnets to hold

it in place. A safety tether is included to prevent the grille

from ever falling from the ceiling.

Saros Express speakers are available in white or black

and can be painted to blend with the ceiling surface.

Prepare Mounting Hole

Front View - Grille Removed

Tighten

Screws

70V

100V

THRU

Terminal Block

Not Shown

Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air

ducts, joists, or other possible obstructions. If applicable, use a good quality stud finder to

locate joists. If there are no obstructions, use the supplied template to trace an outline of

the mounting hole.

For drop tile ceilings, remove the ceiling tile and place on a flat surface to trace the

mounting hole. For drywall or standard construction ceilings, use the template to trace the

mounting hole directly on the ceiling.

Install Cable

Run the cable from the audio source to the speaker location, observing all appropriate

local codes. Strip the ends of the speaker cables approximately 1/8” to 3/16” (~3 mm to

~5 mm) and twist the strands

Install Tile Bridge

The included tile bridge components provide proper support when the speaker is installed

in a typical drop tile ceiling. Refer to the illustration below.

1. Based on the location of the mounting hole determined in “Prepare Mounting Hole”

above, use the two supplied screws to attach the support ring to the rails so that

when installed, the ring is aligned with the mounting hole and the rails rest on the

ceiling grid frame.

2. The support ring position on the rails is adjustable to enable off-center speaker

positioning. The tile bridge assembly can be folded to fit through the speaker cutout in

blind-mount situations.

Speaker Cable Connections

Screw

Cable

Clamp

Speaker

Cable

Terminal

Block

Mounting

Clips

Rear

Cover

Panel

Mount/Remove Speaker

The in-ceiling speaker includes four toggle clamps that simplify the mounting process. If the grille is mounted

on the speaker, remove it before proceeding. (Refer to “Install/Remove Grille” above.)

1. Referring to the illustrations to the right, remove the screw securing the rear cover panel, and lift the

cover panel off to expose the supplied terminal block.

2. Route the speaker cable through the cover cable clamp and connect the wires to the terminal block,

using the outer terminals: red to and black to . Use the inner and terminals to connect a IN + – + – THRU

pass-through (parallel) speaker.

3. Allow some slack in the speaker cable(s) and position the cover panel on the back, making certain it

engages the mounting clips. Secure the cover panel using the screw removed in step 1 and tighten the

cable clamp to secure the cable(s). Do not overtighten. Use a safety tether attached to the rear enclosure

to prevent the speaker from accidentally falling.

4. The toggle clamps offer two positions to accommodate both standard and extra thick surfaces up to

2.4 inches (61 mm). For extra thick tiles, reset the toggle clamps to the upper position before continuing.

a. With the toggle clamps turned inward, insert the speaker into the opening.

b. Hold the speaker against the ceiling and begin tightening the four screws on the front of the speaker.

The toggle clamps first rotate into clamping position (as indicated in the front view illustration to the

right) and then begin holding the speaker to the ceiling.

c. Tighten the screws until the speaker is secure. Do not over tighten.

5. Speaker removal is accomplished by reversing steps 1 through 4 above.

Tile Bridge Assembly

Install/Remove Grille

The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is included to prevent

any possibility of the grille falling from the ceiling. With the tether attached, place the grille in position on

the speaker. To remove the grille, grip the edges and pull away from the speaker.

Paint the Speaker Grille

Speaker grille painting should be done prior to mounting.

1. Carefully remove the material on the underside of the grille and set it aside for reinstallation. It may be

necessary to use a knife or other sharp instrument to free an edge of the material so it can be peeled

away. Use care to avoid cutting or tearing the material.

2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the holes in the grille.

3. Once the paint is dry, reinstall the material to the underside.

Safety Tether

Rigging Points

For SAROS_ICE8T

100V

70V

For SAROS_ICE4T,

and SAROS_ICE6T

100V

70V

20.91 in

(531 mm)

Support

Ring

Screws

(Supplied)

25.92 in

659 mm

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Højttaler
Model:	SAROS ICE4T

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron SAROS ICE4T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Crestron Manualer

Crestron Vector CS1265-RH Manual

24 September 2025

Crestron SAROS ICE6T-B-T-EACH Manual

23 September 2025

Crestron Vector CD1295-RH Manual

23 September 2025

Crestron SAROS ICE4T Manual

7 April 2025

Crestron SAROS ICI6T Manual

7 April 2025

Crestron SAROS IC8T Manual

7 April 2025

Crestron ULTIMATE IC3-SA-WOOFER Manual

28 August 2024

Crestron ULTIMATE IC3-AW-SA-BOX-WOOFER Manual

28 August 2024

Crestron ULTIMATE IC3-AW-SA-TWEETER Manual

28 August 2024

Crestron ULTIMATE IWS82-AW-W-T-EACH Manual

26 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Energy Sistem TempoRave Manual

11 December 2025

RCF C 5215-W MKIII Manual

10 December 2025

RCF X 28 L Manual

10 December 2025

Fostex PM0.4d Manual

8 December 2025

Amphion Argon 3LX Manual

8 December 2025

Amphion Argon 7LX Manual

8 December 2025

8 December 2025

8 December 2025

7 December 2025

7 December 2025