Crestron IRP2 Manual

Crestron Ikke kategoriseret IRP2

Læs gratis den danske manual til Crestron IRP2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 90 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 45.5 anmeldelser. Har du et spørgsmål om Crestron IRP2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates. Use a QR

reader application on your mobile device to scan the QR image.

Description

The Crestron® IRP2 is a pure IR (infrared) emitter that is designed to adhere to the IR

sensor window of a television, an optical disc player, or any other IR-controllable device.

The IRP2 connects to any Crestron control system or room solution box that is equipped

with a 2-pin terminal block-type Crestron IR port, providing a 1-way IR control interface

to the device.

IRP2

IR Emitter Probe

Installation Guide

Installation

Positioning the IRP2

With many devices, the IRP2 works best when positioned directly over the controlled

device’s IR sensor, but with other devices, operation is more consistent when the IRP2 is

placed an inch or two offset from the IR sensor.

It may be difcult to locate the IR sensor on the controlled device, so instead, test

commands from the Crestron control system or room solution box while moving the IRP2

around the controlled device’s front panel. When operation is consistent and reliable,

attach the IRP2 using the procedure below.

Attaching the IRP2

Peel off the clear adhesive strip on the back of the IRP2 shell, and then carefully afx the

IRP2 to the desired location on the controlled device’s front panel while pressing rmly.

Attaching the IR Mask (Optional)

Attach the included IR mask when two or more identical components in the same rack

are being controlled. The IR mask prevents stray IR output from accidentally controlling

another device.

To attach the IR mask, t the two pieces together without removing the clear adhesive

strips from the IRP2 shell or the IR mask, and then attach the IRP2 to the controlled

device as described above.

IRP2 Shell and (Optional) IR Mask (Side View)

Clear adhesive

layer

Internal IR

emitter

output

IRP2

shell

Miniwire

lead

NOTE:

If the IRP2’s shell must be removed and repositioned for any reason, it may

be necessary to replace the adhesive strip with a new piece of two-sided tape

(supplied) to restore adhesion.

NOTE:

The IRP2 is a pure infrared emitter, and it does not emit visible light. Since IR

can be recorded by using a smart device’s digital camera, test to see that the IRP2 is

properly working by triggering the IRP2 using the control system or room solution

box. While the IRP2 is being triggered, record a video of the emitter with a smart

phone’s digital camera. If IR is visible in the video during playback, the IRP2 is

properly working.

mask

(optional)

Clear adhesive

layer

As of the date of manufacture, the device has been tested and found to comply with

specications for CE marking.

Product warranty can be found at www.crestron.com/warranty.

The specic patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specic information, please visit

www.crestron.com/opensource.

Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron

Electronics, Inc. in the United States and/or other countries. Other trademarks, registered

trademarks, and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Crestron disclaims any proprietary interest in the marks

and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Crestron Electronics, Inc. Installation Guide - DOC. 8186D

15 Volvo Drive, Rockleigh, NJ 07647 (2002188)

Tel: 888.CRESTRON 12.16

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Hardware Hookup

Insert the IRP2’s 2-pin connector into an infrared-serial output port of a control system

or a room solution box as shown in the following illustration.

IRP2 Connection Diagram

NOTE: The white-traced wire is positive (+) and connects to the pin labeled “S.”

Hardware Hookup

2-pin connector

IR port

(S G S G)

IR sensor

window

Optical Disk Player

Crestron DM-RMC-200-C

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	IRP2

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron IRP2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron FT2-700-ELEC-PTL Manual

30 Juli 2025

Crestron RMK-AMP-X Manual

30 Juli 2025

Crestron DIN-GWDL-SPLTR Manual

30 Juli 2025

Crestron HD-CTL-101 Manual

30 Juli 2025

Crestron FT2-202-ELEC-PTL Manual

30 Juli 2025

Crestron STIRP Manual

30 Juli 2025

Crestron CSP-LIR-USB Manual

30 Juli 2025

Crestron CEN-IO-COM-202 Manual

30 Juli 2025

Crestron CEN-IO-DIGIN-204 Manual

29 Juli 2025

Crestron DIN-DLI Manual

29 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MiVue Smartbox 3 Manual

1 August 2025

Navman MiVue 850 Manual

1 August 2025

Navman MiVue 690 Manual

1 August 2025

Navman MiVue 145 GPS TAG Manual

1 August 2025

Navman MY30 Manual

1 August 2025

Tripp Lite SPS610HGRA Manual

1 August 2025

AEG E1WYHSK1 Manual

1 August 2025

Thermaltake Pacific R1 Plus Manual

1 August 2025

Olivetti d-Copia 4523MFplus Manual

1 August 2025

Gossen GL SpectroSoft Manual

1 August 2025