Crestron MC3 Manual

Crestron Ikke kategoriseret MC3

Læs gratis den danske manual til Crestron MC3 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Crestron MC3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DO GUIDE

DO Install the Device

The MC3 is designed to be placed onto a at surface.

DO Make Connections

Make the necessary connections as called out in the diagrams

below. Connect power last.

When making connections to the MC3, note the following:

• Use Crestron® power supplies for Crestron equipment.

• The included cable(s) cannot be extended.

NOTE: Ensure the unit is properly grounded by connecting the

chassis ground lug to an earth ground (building steel).

NOTE: The MC3 can be powered via the Cresnet® connection

or with the (included) 24-Vdc power pack.

DO Congure the Control System

The MC3 can be congured using Crestron Toolbox™ software

and the built-in, web-based setup tool.

1. Use Crestron Toolbox to set the time zone. For details,

refer to the Crestron Toolbox help le.

2. Use the Internet Explorer® web browser to navigate to

http://xxx.xx.xx.xxx/setup, where xxx.xx.xx.xxx is the

IP address of the control system. The control system’s

welcome screen is displayed.

NOTE: The web-based setup tool is accessible only from

Internet Explorer.

NOTE: If a security warning is displayed, click Install to

continue.

DO Check the Box

QTY PRODUCT COLOR PART NUM.

1 Connector, 3-Pin Green 2003575

2 Connector, 4-Pin Green 2003576

1 Antenna, 2.4 GHz, 1/4 Wave, Reverse Polarity, Female Black 2001016

1 Power Pack, 24 Vdc, 2.5 A, 100-240 Vac Black 2045873

1 Power Cord, 5' 10" (1.78 m) 2042043Black

1 Cable, USB 2.0, A-B, 6’ (1.83 m) Black 2014966

MC3

3-Series® Control System with Wireless Gateway

COM 1 - 2 Connections

PIN DESCRIPTION

2 RXD - Receive Data

3 TXD - Transmit Data

5 SG - Signal Ground

7 RTS - Request To Send

8 CTS - Clear To Send

• Use with a standard DB9 straight

through cable.

• Pins 1, 4, 6, and 9 are not used but may

be connected.

AUDIO IN (L R):

From Audio Source

AUDIO OUT (L R):

To OSD Device or

Associated Amplifier

VIDEO OUT

(COMPOSITE):

To OSD Device

IR 1–5:

To IR Controlled

Devices

IR IN:

From IR

Device

VIDEO OUT (Y Pb Pr):

To OSD Device

COM 1–2:

To RS-232 Device

LAN:

10/100 Base-T

Ethernet to LAN

NET (24 Y Z G):

To Cresnet Network

RELAY 1–2:

To Controllable

Devices Ground

24 Vdc:

From Power

Supply

USB 1–2:

To USB HID Device

or USB Mass

Storage Device

INPUT:

From Control

Devices

DO GUIDE DOC. 7774C (2043707) 04.16

Specicat ions subject to change without not ice.

3. Click to display the Setup MC3 Setup menu. The MC3 Setup menu displays the IP

address, hostname, and MAC address of the device. It also allows access to various setup

and programming screens.

4. From the MC3 Setup menu, click the following options to congure the control system:

• congures the MC3’s Ethernet settings and displays DHCP, Ethernet Setup

hostname, IP address, subnet mask, default router, domain, and MAC address

settings. In the Ethernet Setup menu, there are additional options:

• Click Advanced Settings to specify DNS servers, web server settings, and SSL

settings.

• Click MyCrestron Dynamic DNS to congure the myCrestron.com Dynamic

DNS service.

• Click Ethernet Diagnostics to test Ethernet communications.

• Click to reboot the MC3.Reboot

• selects programs to be loaded on start-up and controls which Application Setup

programs are running.

• Audo Setup congures the volume for the on-screen display.

• Input/Output Control congures the COM ports, operates the relays, and monitors

the Versiports.

• Video Setup congures the video resolution for the on-screen display.

• displays information about the connected devices, hardware Diagnostics

conguration, and error logs.

• displays rmware information.About

Click to return to the previous screen.

DO Learn More

Visit the website for additional information and the latest rmware updates. To learn

more about this product, use a QR reader application on your mobile device to scan

the QR image.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Cautio n: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s

authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and

its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful

communication.

Industry Canada (IC) Compliance Statement

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit

accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une

antenne d’un type et

d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Le présent émetteur radio , IC: 5683C-CWD6660, a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne

énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types

d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour

l’exploitation de l’émetteur.

Type d’antenne: Dipole, Gain admissible maximal: 2.5 dBi, Impédance: 50 Ohms

Crest ron product development sof t ware is licensed to Crest ron dealers and Crest ron Service Providers (CSPs) under a limited non-exclusive, non-t ransferable Soft ware Development Tools

License Agreement. Crestron product operating system sof tware is licensed to Crest ron dealers, CSPs, and end-users under a separate End-User License Agreement . Both of these Agreements

can be found on the Crestron website at www.crestron.com/legal/soft ware_license_agreement.

The s pecic patents t hat cover Crestron products are listed at . The product warranty can be found at .patent s.crest ron.com www.crestron.com/warranty

Cert ain Crestron products cont ain open source sof tware. For specic information, please visit . www.crestron.com/opensource

Crest ron, t he Crestron logo, 3-Series, Cresnet , and Crestron Toolbox are either trademarks or regist ered t rademarks of Crestron Electronics, Inc. in the United St ates and/or other countries.

Int ernet Explorer is either a trademark or registered trademark of Microsof t Corporation in the Unit ed Stat es and/or other countries. Other trademarks, regist ered trademarks, and trade names

may be used in t his document to refer to either the ent ities claiming t he marks and names or their product s. Crest ron disclaims any proprietary interest in the marks and names of others.