PYNG-HUB
Crestron Pyng
®
Control Hub
crestron.com
|
800.237.2041
> Communicates with the Crestron Pyng
®
App via an
internet connection
> Interfaces with wireless and wired lighting controls,
motorized shades, thermostats, security systems,
door locks, occupancy sensors, daylight sensors,
AV, and other equipment
[2]
> Built-in infiNET EX
®
wireless network gateway
[1,3]
> Cresnet
®
master port for wired devices
[1]
> High-Speed LAN port for Ethernet devices and
internet connection
> Optional COM port expander adds an RS-232
interface for third-party devices
[2]
> Stores system configuration settings onboard
> Cloud backup for reliability and serviceability
> Memory card slot for event logging (Micro SD card not included)
> Crestron “IFE” Integrator Friendly Enclosure
> Surface or DIN rail mountable using bracket provided
> Available rack mount and pole mount options
[2]
> PoE, Cresnet, or line powered
> External 100-240 VAC universal power pack included
The Crestron Pyng
®
Control Hub (PYNG-HUB) communicates with the
Crestron Pyng App (CRESTRON-PYNG) via an internet connection to enable
control and monitoring of AV, lights, shades, thermostats, security systems,
door locks, occupancy sensors, daylight sensors, and other equipment. It
also enables control of the equipment using Crestron
®
touch screens
and keypads.
Built-in infiNET EX
®
, Cresnet
®
, and Ethernet provide both wireless and
wired connectivity to support a wide range of Crestron devices.
[1]
A variety
of third-party devices and services can also connect to the control hub
via Ethernet and the Internet, or via RS-232 using the optional COM Port
Expander (PYNG-CONNECT-COM
[2]
).
System setup and configuration is accomplished by a Crestron authorized
installer using the Crestron Pyng App. Configuration settings are stored
onboard the control hub and backed up in the cloud to ensure reliable
operation and easy serviceability. Simplified internet access is enabled
using the myCrestron Dynamic DNS Service.
SPECIFICATIONS
Wired Communications
Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery,
full/half duplex, industry-standard TCP/IP stack, UDP/IP, CIP, DHCP,
IEEE 802.3at Type 1 compliant
Cresnet: Cresnet master mode
[1]
Wireless Communications
[1]
RF Transceiver: infiNET EX 2-way RF, 2.4 GHz ISM Channels 11-26 (2400
to 2483.5 MHz), default channel 15; IEEE 802.15.4 compliant
Range: 50 ft (15 m) to nearest mesh network device(s), subject to site-
specific conditions and individual device capabilities, range between floors
or ceilings is limited to one level
[3]
Note: Do not rackmount or stack multiple units when using wireless. Use
care when positioning the device to avoid interference from nearby RF
devices, obstructions, and metal surfaces.
Connectors
MEMORY: (1) Micro SD memory card slot;
Accepts one Micro SD card for storage of log files
COMPUTER: (1) USB Type Micro-B connector, female;
Service port for factory use only
NET: (1) 4-pin 3.5 mm detachable terminal block;
Cresnet master port
[1]
;
Outputs power to Cresnet devices if the included power pack is connected
to the 24 VDC power input jack;
Alternately functions as a Cresnet power input to power the unit from a
Cresnet power supply
[2]
;
See “Power” section below for additional specifications
G: (1) 4-40 screw;
Chassis ground lug
24 VDC 0.75A: (1) 2.1 x 5.5 mm DC power connector;
24 Volt DC power input (power pack included);
Passes through to the NET port to power Cresnet devices;
See “Power” section below for additional specifications
LAN PoE: (1) 8-pin RJ45 connector, female;
10Base-T/100Base-TX Ethernet port;
PoE PD port
