Crestron SAROS IC8T-W-T-EACH Manual

Crestron Højttaler SAROS IC8T-W-T-EACH

Læs gratis den danske manual til Crestron SAROS IC8T-W-T-EACH (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 60 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 30.5 anmeldelser. Har du et spørgsmål om Crestron SAROS IC8T-W-T-EACH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Saros® 2-Way In-Ceiling Speakers

quickstart guide

SAROS_IC4T/IC6T/IC8T

www.crestron.com

Specifications subject to

change without notice.

SAROS_IC4T/IC6T/IC8T

Saros 2-way in-ceiling speakers are available in white or

black and may be painted to blend with the ceiling surface.

QUICKSTART DOC. 7387E (2034061) 06.21

Set the Transformer Tap Selector Switch

The speakers are equipped with a 70V/100V matching transformer for distributed audio

systems. The transformer tap selector switch on the front panel is used to set the speaker

power level. Use a flat blade screwdriver to adjust the switch.

1. For SAROS_IC4T 70V systems, use the left side settings and select , , ,1.88 3.75 7.5

15 30, or watts.

2. For SAROS_IC4T 100V systems, use the right side settings and select , , ,3.75 7.5 15

or watts. The position should not be used.30 X

3. For SAROS_IC6T and SAROS_IC8T 70V systems, use the left side settings and

select , , , , or watts.3.75 7.5 15 30 60

4. For SAROS_IC6T and SAROS_IC8T 100V systems, use the right side settings and

select , , , or watts. The position should not be used.7.5 15 30 60 X

The switch may also be set to operation, bypassing the transformer completely. This 8 Ω

setting should be used only for 8 audio systems.Ω

1Installation

Saros ® speakers by Crestron ® deliver professional grade

performance and flexible installation in a range of popular

sizes for demanding commercial applications.

Ideal for use in music, paging, and sound reinforcement

systems, Saros speakers are engineered to achieve

smooth, even coverage, high output, and clear, natural

sound quality through the employment of horn-loaded

titanium dome tweeters, high-efficiency damped cone

woofers, ported enclosures, and precisely tuned cross-

overs.

Prepare the Mounting Hole

Front View - Grille Removed

Tighten Screws

70V 100V

THRU

Terminal Block

Not Shown

Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air ducts,

joists, or other possible obstructions. If applicable, use a good quality stud finder to locate joists.

If there are no obstructions, use the supplied template to trace an outline of the mounting hole.

For drop tile ceilings, remove the ceiling tile and place on a flat surface to trace the mounting

hole. For drywall or standard construction ceilings, use the template to trace the mounting hole

directly on the ceiling.

Install the Speaker Cable

Run the speaker cable (not included) from the audio source to the speaker location, observing

all appropriate local codes. Strip the ends of the speaker cables approximately 1/8 in. to 3/16 in.

(~3 mm to ~5 mm) and twist the strands .

Install the Tile Bridge

The included tile bridge components provide proper support when the speaker is installed in a

typical drop tile ceiling. Refer to the illustration below.

1. Based on the location of the mounting hole determined in the “Prepare the Mounting Hole”

section (above), use the two supplied screws to attach the support ring to the rails so that

when installed, the ring is aligned with the mounting hole and the rails rest on the ceiling

grid frame.

2. The support ring position on the rails is adjustable to enable off-center speaker positioning.

The tile bridge assembly can be folded to fit through the speaker cutout in blind-mount

situations.

Connect Speaker Cable

Screw

Cable

Clamp

Speaker

Cable

Terminal

Block

Mounting

Clips

Rear

Cover

Panel

Mount or Remove the Speaker

The in-ceiling speaker includes four toggle clamps that simplify the mounting process. If the grille is mounted

on the speaker, remove it before proceeding. (Refer to “Install or Remove the Grille” above.)

 Referring to the illustrations to the right, remove the screw securing the rear cover panel, and lift the cover

panel off to expose the supplied terminal block.

 Route the speaker cable through the cover cable clamp and connect the wires to the terminal block, using

the outer IN terminals; red to + and black to –. Use the inner + and – THRU terminals to connect a pass-

through (parallel) speaker.

 Allow some slack in the speaker cable and position the cover panel on the back, making certain it

engages the mounting clips. Secure the cover panel using the screw removed in step 1, and tighten the

cable clamp to secure the cable. Do not overtighten. Use a safety tether ( (not included))

SPKA-ST-15

attached to the rear enclosure to prevent the speaker from accidentally falling.

 The toggle clamps offer two positions to accommodate both standard and extra thick surfaces up to 2.4 in.

(61 mm). For extra thick tiles, reset the toggle clamps to the upper position before continuing.

D With the toggle clamps turned inward, insert the speaker into the opening.

E Hold the speaker against the ceiling and begin tightening the four screws on the front of the speaker.

The toggle clamps first rotate into clamping position (as indicated in the front view illustration to the

right), and then begin holding the speaker to the ceiling.

F Tighten the screws until the speaker is secure. Do not overtighten.

 Speaker removal is accomplished by reversing steps 1 through 3 above.

D Hold the speaker in position and loosen the front screws to unclamp the speaker. Continue to loosen

the screws until the toggle clamps rotate inward.

E When the

speaker is loose, carefully lower the speaker from the opening and disconnect the wiring.

Tile Bridge Assembly

26.00 in.

(661 mm)

Screws

(Supplied)

Adjustable

Rails

Support

Ring

Install or Remove the Grille

The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is included to prevent

the grille falling from the ceiling. With the tether attached, place the grille in position on the speaker. To

remove the grille, grip the edges and pull away from the speaker.

Paint the Speaker Grille

Painting the Speaker grille should be done prior to mounting.

1. Carefully remove the mesh on the underside of the grille, and set it aside for reinstallation. It may be

necessary to use a knife or other sharp instrument to free an edge of the mesh so it can be peeled

away. Use care to avoid cutting or tearing the mesh.

2. Dry brush or lightly spray paint the grille. Use care to avoid clogging the holes in the grille.

3. Once the paint is dry, reinstall the material to the underside of the grille.

Safety Tether

Rigging Points

For SAROS_IC4T

For SAROS_IC6T,

and SAROS_IC8T

70V100V

Saros® 2-Way In-Ceiling Speakers

SAROS_IC4T/IC6T/IC8T

www.crestron.com

Specifications subject to

change without notice.

QUICKSTART DOC. 7387E (2034061) 06.21

The specific patents that cover crestron products are listed at patents.crestron.com.

Crestron th Crestro log an Sa ar eithe trademar o registe trademar o Crestron , e n o d ros e r ks r red ks f

Electro Inc. t Unite Stat and/o othe countries Othe trademar registered nics, , in he d es r r . r ks,

trademark an t name ma b use i thi documen t refe t eithe t entitie claiming s, d rade s y e d n s t o r o r he s

th mar an na o thei products Crestr disclaim an proprietar inter i th marks e ks d mes r r . on s y y est n e

an name other Crestro no responsib fo error i typograph o photography.d s of s. n is t le r s n y r

This document was written by the echnical Publications department at Crestron.T

3Specifications

SPECIFICATION

SAROS_IC4T, IC6T, IC8T

SAROS IC4T SAROS_IC6T SAROS_IC8T_

Further Inquiries

To locate specific information or resolve question after reviewing thi guide, s s

contact Crestron True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for

assistance within a particular geographic region, refer to the listing of Crestron

worldwide offices at ( ).

www.crestron.com/offices

To post a question about Crestron products, log onto Crestron’s Online Help at

www.crestron.com/onlinehelp. First-time users must establish a user account to

full benefit from all available features.y

TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION

No sound or

intermittent

sound is

coming from

the speakers.

There is a cable

connection error.

Verify the cable connections

between the amplifier and

speakers.

The amplifier is not

receiving an input signal or

there is a malfunction.

Verify that the amplifier is

functioning correctly, that it is

receiving an input signal, and

that the correct input source is

selected.

There is a faulty device in

the system.

Verify that all system devices

are functioning properly.

Constant noise

such as buzz,

hum, or hiss is

coming from

the speakers.

There is a system

grounding fault.

Verify that system grounding is

correct.

The low-

frequency

output is poor.

There is an incorrect

polarity connection at the

speaker or amplifier.

Verify speaker connection

polarity (+ on amplifier to + on

speaker).

4Problem Solving

Troubleshooting

The following table provides corrective action for possible trouble situations. If

further assistance is required, please contact a Crestron True Blue Support

at 1-888-CRESTRON [1-888-273-7876].

2Physical Views

Rear and Side Views (Typical)

Construction

Enclosure Zinc-plated steel, plenum-rated, 0.5 in. (13 mm) or 0.75 in. (19 mm) in conduit knockout

top and side

Baffle ABS UL94V-0 plastic

Grille Steel with textured finish, paintable, magnetically held zero-bezel frameless, safety tether

Mounting Flush ceiling mount using 4 integral 2-step toggle clamps, 2.4 in. (61 mm) maximum

surface thickness, tile bridge included. (2) rigging points for safety tether,

(SPKA-ST-15 sold separately)

Recommended

Cutout Diameter

Diameter

Minimum

Mounting Depth

Front View - Grille Removed (Typical)

8.53 in. (217 mm) not

including toggles

7.13 in. (181 mm)

7.70 in. (195 mm)

6.90 in. (176 mm)

7.1 lb (3.2 kg)

10.57 in. (269 mm) not

including toggles

8.31 in. (211 mm)

9.68 in. (246 mm)

8.10 in. (206 mm)

10.4 lb (4.7 kg)

12.07 in. (307 mm) not

including toggles

9.10 in. (231 mm)

11.20 in. (285 mm)

8.90 in. (226 mm)

12.5 lb (5.7 kg)

Dimensions

Diameter

Depth

Recommended

cutout diameter

Minimum mounting

depth

Weight

Connections

Input (1) 4-pin 5-mm detachable terminal block with screw-down flanges;

Speaker input with parallel pass-through;

Maximum Wire Size: 12 AWG

Controls

Transformer Tap (1) Recessed 5-position screwdriver adjustable rotary switch on baffle;

Used to select 70V/100 V tap settings or (bypass)8 Ω

Environmental

Temperature -2° to 120°F (-19° to 49°C)

Humidity 5% to 95% RH (non-condensing)

100V70V

8.0 in. (203 mm)

polypropylene with ring

mode decoupled cloth

surround and steel basket

0.98 in. (25 mm) titanium

dome, 90° conical

horn-loaded

2.5 kHz

8 Ω nominal with

transformer set to 8 Ω

3.75, 7.5, 15, 30, 60 watts

at 70V; 7.5, 15, 30, 60

watts at 100V

50 Hz to 20 kHz (±3 dB)

40 Hz to 20 kHz (-10 dB)

150 watts program, (8 Ω)

90.5 dB @ (W/m)

95° conical (nominal)

6.5 in. (165 mm)

polypropylene with ring

mode decoupled cloth

surround and steel basket

0.98 in. (25 mm) titanium

dome, 90° conical

horn-loaded

2.5 kHz

8 Ω nominal with

transformer set to 8 Ω

3.75, 7.5, 15, 30, 60 watts

at 70V; 7.5, 15, 30, 60

watts at 100V

50 Hz to 20 kHz (±3 dB)

40 Hz to 20 kHz (-10 dB)

125 watts program (8 Ω)

88.5 dB @ (W/m)

100° conical (nominal)

4.0 in. (102 mm)

polypropylene with ring

mode decoupled cloth

surround and steel basket

0.79 in. (20 mm) titanium

dome, 110° conical

horn-loaded

2.0 kHz

8 Ω nominal with transform-

er set to 8 Ω

1.88, 3.75, 7.5, 15, 30 watts

at 70V; 3.75, 7.5, 15, 30

watts at 100V

60 Hz to 20 kHz (±3 dB)

45 Hz to 20 kHz (-10 dB)

100 watts program, (8 Ω)

85.0 dB @ (W/m)

110° conical (nominal)

Woofer

Tweeter

Crossover Frequency

Impedance

Transformer Taps

Frequency Response

Frequency Range

Power Handling

Sensitivity

Coverage

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Højttaler
Model:	SAROS IC8T-W-T-EACH

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron SAROS IC8T-W-T-EACH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Crestron Manualer

Crestron ULTIMATE IC3-SA-WOOFER Manual

28 August 2024

Crestron ULTIMATE IC3-AW-SA-BOX-WOOFER Manual

28 August 2024

Crestron ULTIMATE IC3-AW-SA-TWEETER Manual

28 August 2024

Crestron ULTIMATE IWS82-AW-W-T-EACH Manual

26 August 2024

Crestron ULTIMATE IWLCR62-W-T-EACH Manual

26 August 2024

Crestron ULTIMATE ICS8-AW-W-T-EACH Manual

25 August 2024

Crestron SAROS ICT5T-22 Manual

25 August 2024

Crestron ULTIMATE IC6-AW-W-T-EACH Manual

25 August 2024

Crestron ULTIMATE IC8-AW-W-T-EACH Manual

25 August 2024

Crestron Ultimate IGS12T-PRIMED-EACH Manual

23 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

LENRUE A2 Manual

15 Juni 2025

Sony BRAVIA Theatre Bar 6 Manual

15 Juni 2025

Hecate G1500 SE Manual

15 Juni 2025

Edifier MP330 Manual

15 Juni 2025

Hecate G1500 Manual

14 Juni 2025

XLEADER SoundAngel A8 Manual

14 Juni 2025

RCF DU 31EN Manual

14 Juni 2025

Omnitronic PS-2.5WB Manual

14 Juni 2025

Greadio R-919 Manual

14 Juni 2025

J.W. SPEAKER 8700 Evolution J2 Manual

14 Juni 2025