Crivit BG 2010 Manual

Crivit Ikke kategoriseret BG 2010

Læs gratis den danske manual til Crivit BG 2010 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Crivit BG 2010, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

0123 / 14

Components of the camping stove BG 2010

The device consists of 1 upper part of the camping stove (also upper

part), 2 butane cartridges of 190 g (No. 52150), 1 lower part of the

camping stove  cartridge holder (also lower part), and 1 set of Instructions

for Use. Please check the completeness of the article.

Intended use

Camping Stove with Gas Cartridge BG 2010 is intended for private use

(e.g. cooking tee, warming up tinned food, etc.) and can be operated

only outside.

Important:

Please read these instructions for use carefully before you attach the

gas cartridge to get acquainted with the device first. Keep the leaflet for

further reference.

It is not allowed to change settings or make modifications from those

set by the manufacturer. It could be dangerous to change the structure

of the device on your own authority, to remove parts or to use parts

which are not approved by the manufacturer.

Use solely butane gas cartridges of the type 200, picture 1, according

to EN 417 (190 g), which are commercially available, which are

recommended for this device and which correspond with the European

Norm EN 417 (as e.g. butane cartridges provided  CFH No. 52150).

Butane gas cartridges of 190 g you use must have an inscription EN

417. These standard gas cartridges are available in building stores. This

device may be only used with a pressure gas cartridge (cartridge with

a piercing point connection  CFH No. 52150). It could be dangerous

to connect other gas receptacles.

Never fit a gas receptacle (butane cartridge of 190 g) before reading the

instructions on it.

Use only outside.

Sec ur i ty i n s tr u ct io n s an d war n i n g s

·Do not unscrew the lower part of the cartridge holder, until the butane

cartridge is completely empty (shake it a little if splashing of liquid is

audible). Otherwise there is imminent danger of gas escaping which

could ignate next to a heat source and thus cause a really dangerous

situation .(danger of explosion)

·Make sure before attaching the gas cartridge that the gasket (between

the device and the gas cartridge) is not missing and is in good condition

(see drawing above  picture 5). The rubber gasket is easily visible

Instructions for Use

No. 48830 Camping Stove BG 2010

IAN 97029

EN CY

picture 1 picture 2 picture 3 picture 4

gas regulation

valve

picture 5 safety latch

black

rubber gasket

if you hold the upper part of the camping stove as shown on picture

5. It is necessary that there is a black rubber gasket inside on the

piercing pin and that it is in a good condition. If this gasket is missing

do not use the device (danger of leakage).

·Do not use any device with damaged or worn out gasket. Do not use

any device which is leaking or damaged or which does not work

properly.

·Only fit the gas cartridge when outside, where there are no flammable

materials or combustible sources in the neighbourhood, no electric

stoves or open fire, and in a sufficient distance from other persons.

Do not smoke when fitting the cartridge.

·Do not change the butane cartridges if you are not absolutely sure

that the cartridges are completely empty. Follow safety instructions

stated on the butane cartridge.

·Keep the device away from children. Children are not allowed to use

the device (danger of injury).

·Do not shake the device immediately before starting up, in order that

the liquid gas cannot flow to the burner and cause problems with

lighting.

·Use the camping stove only on a horizontal level.

·Only change the cartridge when outside, far away from possible

combustible sources, as e.g. open fire, pilot flames, electrical hot

plates and similar, and away from other persons and animals. Before

changing the butane cartridge always close the gas regulation valve.

·Used butane gas cartridges are one-way receptacles. Refilling is not

permitted and could be very dangerous.

·Protect the butane cartridge and the device from direct exposure to

sun light (impact of heat). Do not expose it to temperatures over 50°C.

·Do not use in closed rooms. Make sure the device is used only

outside  do not use it in shafts or below ground level, because the

gas here is heavier than air and it can spread without control.

·The device must always be positioned on a stable and horizontal

basis.

·Do not use it in a tent - danger of suffocation due to a quick consumption

of oxygen or danger of fire.

·Use the device only at a safe distance from inflammable materials (at

least 500 mm from the walls and 1500 mm from the ceiling). Make

sure that the rising heat and vapours do not endanger the ceiling.

Prevent accumulation of heat, eventually increase the safe distance

to the ceiling.

·The device can reach very high temperatures at the burner during

normal operation.

·Do not leave the device unattended if it is on. Protect the butane

cartridge from becoming warm or hot. Prevent accumulation of heat.

·ATTENTION: Accessible parts of the device can be very hot. Keep

small children away from the device Never touch(danger of injury).

the burner if it is still hot. When the device is not in use, protect it from

dust and humidity. Never keep the device below ground level.

·If the flame is blown out due to a wind blast, immediatelly close the

gas regulation valve, so that no more gas can flow uncontrolled out

of the device.

·Do not use the device close to inflammable or heat sensitive materials

(danger of fire).

·Do not make any modifications to the device. Malfunctions can be

only fixed by an authorized specialist dealer or by the manufacturer.

Repairs can be done only by an authorized specialist dealer or by

the manufacturer.

·If gas leaks out of your device (you can smell gas) take it immediately

outside to a place with a good air circulation and without any combustible

sources, where you can search for the leaking spot and fix it. Only

test gas tightness of your device when outside. Never search for

untight connections using a flame, use always soapsuds.

·Use only cooking pots with a maximum diameter of and a 20 cm

maximum height of . When using bigger cooking pots, heat 12 cm

could accumulate and the stove could get damaged. When cooking

ensure there is a safe distance between the pot rim and the level

inside, so that the cooking water cannot spurt out.

·Use the stove only on a stable and even base.

Test for leaks

Only test gas tightness when outside by spreading soapsuds over the

connections at the outer side of the device, where the gas flows, or spray

these connections with a leak-seeking-spray. Never search for untight

connections using a flame, use always either soapsuds or a leak-seeking-

spray! Do not put a device into operation with damaged or worn out

gaskets. Never use a device where gas is leaking, which is damaged

or does not work properly.

Setting the size of the flame

It is possible to regulate the size of the flame by turning the black gas

regulation valve (see picture 4 / (+) = open gas supply, (-) = shut gas

supply). By turning the gas regulation valve in direction (+) the gas supply

is opened. By turning further in direction (+) the gas flow reaches its full

Löt- und Gasgeräte GmbH

Bahnhofstraße 50, D-74254 Offenau

Tel. +49 7136 9594-0

Fax +49 7136 9594-44

Internet: www.cfh-gmbh.de

E-Mail: info@cfh-gmbh.de

Stand: VO-12.13

performance (big flame). By turning the gas regulation valve in direction

(-) the gas flow decreases (small flame).

Steps to be taken before attaching the butane gas cartridge

Only change cartridge when outside and far away from other persons.

After each attachment or a change of a cartridge you must carry out a

test for leaks (see Test for Leaks). Make sure that all attachments and

other connections are correctly connected and nothing is damaged.

Ensure that parts where the gas flows are not damaged. Never use a

damaged device. Before attaching the butane cartridge, close the gas

regulation valve on the device (see picture 4 / (-) switch off gas supply).

Before attaching each new gas receptacle check the gasket (visual check

 picture 5). It is necessary to ensure that at the upper part of the

stove inside on the piercing pin there is a black rubber gasket, and

that this gasket is in a good condition (see drawing - picture 5). If

this gasket is missing or is damaged do not use the device. The

replacement gasket can be changed only by an authorized specialist

dealer or the manufacturer. Do not make any alterations to the

device! Make sure, always before you light the flame on the burner that

all parts are gastightly connected.

Attaching the butane cartridge

When assemblying the device hold it upright (burner pointing upwards

and the bottom of the lower part of the camping stove  cartridge holder

- pointing downwards). Screw all parts together precisely and without

interruption. Do not strip the screw thread.

Close the regulation valve on the upper part of the device by turning it

clockwise (-) (see drawing - picture 4). Place the butane gas cartridge

into the cartridge holder (see drawing - picture 2). Now screw the cartridge

holder gastightly to the upper part (see picture 3), till the latch at the side

snaps (see picture 5).

Changing the butane cartridge

It is possible to change the butane cartridge only if it is completely empty

(see section headed Security instructions  Warning). Check that the

cartridge is empty before changing (shake it a little if splashing of liquid

is audible). Make sure the flame on the burner is extinguished before

loosening the cartridge. You can loosen the lower part from the upper

part by pressing the security latch at the side (see picture 5) and rotating

the lower part counterclockwise (picture 1). Take the empty butane

cartridge from the lower part of the device and dispose of it accordingly.

Now you can attach a new butane cartridge (see Steps by attaching the

butane cartridge).

How to operate the device

After properly fitting of the butane cartridge and testing for leaks (to be

carried out outside), turn now the gas regulation valve by about a half

rotation counterclockwise towards (+). Light the flame on the burner tip

with a match or a lighter and only now turn on completely the gas

regulation valve, so that the flame can reach its highest performance.

Do not shake the device immediately before lighting the burner and after

having lit it do not move it any more. Otherwise there is a danger that

the liquid gas will leak and an uncontrolled flame will ignite. Place the

device on . Wind could extinguish an even surface protected from wind

the flame and the gas could further escape from the device  danger

of injury or burn. In a case the flame extinguishes uncontrolled (e.g.

wind blast) immediately turn off the gas regulation valve (see picture 4

/ (-) = switch off gas supply) and restart the device again as described

above. Use the device only in an upright position and under a permanent

supervision of adult persons.

Switching off the device

By turning the gas regulation valve clockwise to the right (-) (see picture

4) the supply of gas is stopped and the flame extinguishes. Have in mind

that the burner is still very hot and that it must cool down before it is

stored.

Storage and transport

Follow the safety instrauctions stated on the butane cartridge.

Storage: Store the device in a vertical position!. store the deviceNever

or the butane cartridges below ground level (e.g. cellar, boiler room).

Storing area must be sufficiently ventilated.

Transport: Ensure that the device stands securely upright and it must

not fall over or fall down. Always secure the device during the transport.

Care of the device + Repair service

It is allowed to use only recommended spare parts. Do not use a device

where any parts are damaged. Any repairs as well as replacement of

the nozzle can be carried out only by an authorized specialist dealer for

liquid gas or by the manufacturer. In case of a repair contact the

manufacturer at the maintenance address below. The nozzle is marked

with 22 (nozzle No. 22  corresponds with the nozzle diameter of 0,22

mm). Do not make any modifications to the device.

Changing the gasket

When changing the gasket the wider lower rim of the new gasket must

fit precisely to the gasket holder on the piercing pin. The rubber gasket

can be replaced only by an authorized specialist dealer or by the

manufacturer.

Cleaning the device

It is possible to clean the device with a dry cloth only when the burner

has cooled down. Do not use any cleansing agents because the openings

in the burner and the nozzle could become blocked.

Warranty

The warranty for this device is 3 years from the date of purchase. The

warranty starts with the date of purchase. Please keep the original receipt

in a safe place. This document is required as a proof of purchase. If any

material or manufacturing defects occur within 3 years from the date of

purchase of this product, the product will be either repaired or replaced

free of charge for you - at our discretion. This guarantee presumes that

you submit the defective device and the proof of purchase (receipt)

together with a short description of the defect and when the defect

occurred within 3 years. In case that the defect is covered by our warranty,

you will receive either the repaired product or a new one. In case of a

warranty claim, please contact us by E-Mail under info@cfh-gmbh.de.

We will contact you immediately.

Environmental instructions

The gas used is environment-friendly liquid gas, which does not burden

or damage the environment and it is not dangerous for the ozone layer.

The butane cartridge or its contents do not have a restricted shelf-life.

Follow the regulations for the liquid gas.

Disposal of the butane cartridge

Totally emptied butane cartridges must be disposed of by using the

Dual recycling system. Butane cartridges, which are not completely

empty have to be disposed of at collection centres for harmful substances.

Disposal of the device

The device is produced of recyclable materials. To dispose of or to

recycle this device, get in touch with an authorized local Recycling Office

or a waste disposal company.

Technical data

Gas type: butane, unregulated, in a pressure gas

cartridge

Related heat input: appx. 70 g/h

appx. 0,97 kW

Nozzle No. 22

Nozzle: Ø 0,22 mm

Device category: vapor pressure butane (I3)

Burning time with 1 butane cartridge approximately 2,5

hours

The performance in the operating manual applies to measurement results

with test gas under test conditions. When using the provided butane

cartridge under normal conditions, deviations in the related heat input

can occur. ( ant information: The ambient temperature has anImport

essential influence on the performance of the device. As a general

rule is that the performance decreases at low temperatures).

We wish you much pleasure with your Camping Stove.

Technical and optical parameters subject to change

Status: 12/2013

Maintenance address and manufacturer:

Produkt Specifikationer

Mærke:	Crivit
Kategori:	Ikke kategoriseret
Model:	BG 2010

Har du brug for hjælp?

Hvis du har brug for hjælp til Crivit BG 2010 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crivit Manualer

Crivit IAN 383243 Manual

29 Juli 2025

Crivit IAN 278515 Manual

28 Juli 2025

Crivit IAN 284742 Manual

27 Juli 2025

Crivit IAN 311967 Manual

27 Juli 2025

Crivit IAN 358697 Manual

27 Juli 2025

Crivit IAN 327345 Manual

27 Juli 2025

Crivit IAN 383694 Manual

27 Juli 2025

Crivit IAN 327349 Manual

27 Juli 2025

Crivit IAN 391389 Manual

27 Juli 2025

Crivit IAN 282717 Manual

27 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Globe GVP20A Manual

3 September 2025

Deye SUN-7.6K-SG05LP1-EU-AM2-P Manual

3 September 2025

Kool-It Signature KCB-83-4 Manual

3 September 2025

SRS SR400 Manual

3 September 2025

Turbo Air M3H24-1 Manual

3 September 2025

Biltema 84-187 Manual

3 September 2025

Steinel UI2 KNX Manual

3 September 2025

SRS DG645 Manual

3 September 2025

Scotsman NH1322-A Manual

3 September 2025

Stamos S-PLASMA 85CNC Manual

3 September 2025