Crunch DR-1325.4D Manual

Crunch Modtager DR-1325.4D

Læs gratis den danske manual til Crunch DR-1325.4D (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Crunch DR-1325.4D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Place terminal in a secure

position so that it won’t

accidentally contact the

negative battery post

Power / Ground

cable size

It is critical to use the proper

power and ground cable. Select

the size listed here for your

amplier model. Always use high

quality copper cable.

Cable size recommendations for

multi amp systems are available

on our website.

Properly route power,

speaker and RCA cables

through the vehicle.

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplier to

a secure surface. Do not mount

the amplier upside down.

Using spade terminals, connect the

+12V to the power cable from the

battery, the REM to the source unit

turn-on wire and the GND to the

chassis ground..

Bare metal

Connect the RCA cables to

the INPUT connectors. The

OUTPUT can be used to

provide input for a second

amplier.

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Re-connect the negative

battery terminal making sure it

is securely tightened.

The chassis ground connection is

critical to the performance of the

amplier. Choose a location that is

close to the amplier. Completely

scrape away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Disconnect

negative battery

terminal

Run Cables

Mount Amplier

Power

Connections

Signal Input

Low Level RCA

Positive Battery

Connection

Re-connect

Negative Battery

Terminal

Chassis Ground

Be prepared to disarm your vehicle’s alarm and

to enter your radio / source unit code.

Installation

Before you start

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

Turn the LEVEL control completely

counter-clockwise to minimum.

Level Control

4ga

Model Fuse Size Cable Size

External 60A

External 80A

External 100A

External 150A

External 100A

External 125A

External 60A

External 80A

Common System Setup

4ch - Full Range

4ch - Mixed Mono

Mono

2ch

DR-1325.1

DR-2125.1D

DR-2725.1D

DR-3725.1D

DR-2125.2D

DR-3125.2D

DR-1325.4D

DR-2525.4D

CR-U-01

Produkt Specifikationer

Mærke:	Crunch
Kategori:	Modtager
Model:	DR-1325.4D

Har du brug for hjælp?

Hvis du har brug for hjælp til Crunch DR-1325.4D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Crunch Manualer

Crunch DR-3125.2D Manual

22 August 2025

Crunch GPX1500.4 Manual

22 Juli 2025

Crunch GPX5500.1D Manual

14 Juli 2025

Crunch GPX1250.1D Manual

11 Juli 2025

Crunch Gravity GTX1600.4D Manual

8 Juni 2025

Crunch Gravity GTX2400.4D Manual

8 Juni 2025

Crunch GPX1600.1D Manual

20 Februar 2025

Crunch Ecomaxx CRE400.4DSP Manual

20 Februar 2025

Crunch DR-1325.4D Manual

6 September 2024

Crunch DR-2525.4D Manual

6 September 2024

Modtager Manualer

Nyeste Modtager Manualer

Atoll MA100 Manual

8 December 2025

Fostex AP25 Manual

7 December 2025

Fostex PC200USB-HR Manual

7 December 2025

Atoll CD400 Evolution Manual

7 December 2025

Fostex PC200USB Manual

7 December 2025

Fostex AP05 Manual

6 December 2025

Atoll AV500 Manual

6 December 2025

Atoll AV100 Manual

5 December 2025

Atoll AM300 Evolution Manual

5 December 2025

AVM Evolution AS 3.3 Manual

5 December 2025