CRUX CS-CR41 Manual

CRUX Ikke kategoriseret CS-CR41

Læs gratis den danske manual til CRUX CS-CR41 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 14 anmeldelser. Har du et spørgsmål om CRUX CS-CR41, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
RADIO REPL ACEMENT
R
INTERFACING SOLUTIONS
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030520
CS-CR41
Radio Replacement with SWC Retention for
CHRYSLER, DODGE and JEEP Vehicles
1 of 3
PRODUCT FEATURES:
NOTES:
PARTS INCLUDED:
- Retains factory features in select Chrysler, Dodge and Jeep vehicles while funconing with an aermarket radio.
- Retains Steering Wheel Controls via built-in, pre-programmed interface.
- Supports amplied and non-amplied systems.
- Provides reverse trigger for rear view camera.
- EIA color coded wiring for easy installaon.
1. The Front and Rear fading are NON-Adjustable on amplied systems.
2. Also supports radio replacement in vehicles with 4.3” and 8.4” color screens.
3. Does not retain Uconnect.
CS-CR41 MODULE Audio Filter1st Gen Harness 2nd Gen Harness SWC Cables
INSTALLATION DIAGRAM:
The CS-CR41 includes 2 harnesses for older and new model vehicles. Only 1 of the harness connectors
will t into your radio. See installaon diagrams below for each harness.
1st Generaon Harness
TO FACTORY
HARNESS
12-Pin Black
Connector
First Generation Harness
*Does not supply Reverse Trigger on Manual Transmissions. Reverse trigger wire from the
aftermarket radio and/or camera power must be connected to factory reverse light wire instead.
1 2 3
ON
4-Pin
Connector
Option A:
Option B:
Cap or insulate if
not being used
BLUE / YELLOW Insulate with tape
if not being used
3.5MM SWC CABLES (Option A or B)
Use the proper 3.5MM to 4-Pin cable for your radio.
Plug in the selected 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
AFTERMARKET
RADIO
VSS (Vehicle Speed Sense) Pink
Illumina�on (+) Orange
Power Antenna/Amp Turn on Blue/ White
Reverse Trigger* Purple/White
+12V Constant Yellow
+12V ACC Red
Ground Black
AMPLIFIED
NON AMPLIFIED
See page 2 for
speaker wire
connections
Audio
Filter
RADIO REPL ACEMENT
R
INTERFACING SOLUTIONS
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030520
CS-CR41
Radio Replacement with SWC Retention for
CHRYSLER, DODGE and JEEP Vehicles
2 of 3
AFTERMARKET
RADIO
TO FACTORY
HARNESS
12-Pin Black
Connector
Second Generation Harness
*Does not supply Reverse Trigger on Manual Transmissions. Reverse trigger wire from the
aftermarket radio and/or camera power must be connected to factory reverse light wire instead.
4-Pin
Connector
Option A:
Option B:
Cap or insulate if
not being used
BLUE / YELLOW Insulate with tape
if not being used
Use the proper 3.5MM to 4-Pin cable for your radio.
Plug in the selected 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
1 2 3
ON
VSS (Vehicle Speed Sense) Pink
Illumina�on (+) Orange
Power Antenna/Amp Trun on Blue/ White
Reverse Trigger* Purple/White
+12V Constant Yellow
+12V ACC Red
Ground Black
AMPLIFIED
NON AMPLIFIED
See below for
speaker wire
connections Audio
Filter
2nd Generaon Harness
NON AMPLIFIED SYSTEMS AMPLIFIED SYSTEMS
Plug the 4-pin Molex connector to the NON-AMPLIFIED
side of the inline lter.
Plug the 4-pin Molex connector to the AMPLIFIED
side of the inline lter.
Wire Connecons: Wire Connecons:
Aermarket Radio CS-CR41 Harness Aermarket Radio CS-CR41 Harness
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Green
Green/Black
Purple
Purple/Black
Not Used
Not Used
Not Used
Not Used
Speaker wire connecons:
Wire the audio lter using the connecon chart below. Plug the 4 pin Molex plug found on the 1st and 2nd
generaon harnesses to the corresponding 4 pin Molex socket on the audio lter. (Amplied or Non-Amplied)

Produkt Specifikationer

Mærke: CRUX
Kategori: Ikke kategoriseret
Model: CS-CR41

Har du brug for hjælp?

Hvis du har brug for hjælp til CRUX CS-CR41 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret CRUX Manualer

CRUX

CRUX DKGM-51 Manual

23 August 2025
CRUX

CRUX RVCFD-79F Manual

23 August 2025
CRUX

CRUX ACP-TSL Manual

23 August 2025
CRUX

CRUX RVCCH-75WT Manual

22 August 2025
CRUX

CRUX VIMMB-85N Manual

10 Juli 2025
CRUX

CRUX VIMPR-90P Manual

10 Juli 2025
CRUX

CRUX VIMCF-93C Manual

10 Marts 2025
CRUX

CRUX VIMFD-95F Manual

10 Marts 2025
CRUX

CRUX VIMCF-93 Manual

10 Marts 2025
CRUX

CRUX VIMAD-84 Manual

10 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo

Kimo LR 110 Manual

2 September 2025
HMS Premium

HMS Premium LPD02 Manual

2 September 2025
AVer

AVer E1008 Manual

2 September 2025
Biltema

Biltema 17-547 Manual

2 September 2025
Groen

Groen AH/1E Manual

2 September 2025
ACOPower

ACOPower HY-P30 Manual

2 September 2025
Yamaha

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025
Globe

Globe RG30 Manual

2 September 2025
Deye

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025
Neutrik

Neutrik NLT4FXX Manual

2 September 2025