CRUX VIMBM-87 Manual

CRUX Ikke kategoriseret VIMBM-87

Læs gratis den danske manual til CRUX VIMBM-87 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om CRUX VIMBM-87, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

TO FACTORY

HARNESS

F-OPTIC

(male plug)

F-OPTIC

(male plug)

INTERFACE

F-OPTIC

(female plug)

BLUE/ VIDEO DEACTIVATION

BLACK/ GROUND

RED/ 12V CONSTANT

3-PIN

(male plug)

SAFETY WARNING:

THIS INTERFACE IS DESIGNED TO ACTIVATE

VIDEO IN-MOTION TO ALLOW THE PASSENER

ACCESS TO THE ADDRESS INPUT WHILE THE

VEHICLE IS IN-MOTION. THIS INTERFACE MAY

CAUSE AN ERROR WHEN SERVICED AT THE OEM

DEALER. BE AWARE THAT MOST DEALERS

WILL ATTEMPT TO VOID THE MANUFACTURERS

WARANTY WHEN INSTALLING ANY AFTERMARKET

EQUIPMENT. IMPROPER USE OF THIS INTERFACE

BY THE DRIVER MAY RESULT IN CITATION. DRIVER

MUST KEEP FULL ATTENTION ON THE ROAD AND

RESPOSIBILITY ON THE SAFETY OF HIS

PASSENGERS.

INTERFACING SOLUTIONS

VIDEO IN-MOTION ACTIVATION FOR BMW CIC2 F-SERIES PROFESSIONAL NAV SYSTEM

BMW

2010 - 2012 5 Series

2011 - 2013 6 Series

2009 - 2012 7 Series

2009 - 2012 GT5

2010 - 2013 X3

ONLY COMPATIBLE WITH:

- CIC2 PROFESSIONAL NAV

SYSTEM

VIMBM-87

We recommend reading this installation guide rst before starting any

work. Following these instructions from “Start” to” Finish” will ensure

a smooth and hassle free installation. We oer telephone support M-F

9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.

PARTS INCLUDED:

(1) BM-87 Interface

(1) BM-87 Fiber Optic Harness

(1) Instruction

PRECAUTIONS:

- Remove the negative side of the battery to avoid any short circuits

durring the installation.

- Do not install the interface near any major components or near the

HVAC system. This may cause damage or overheating to the vehicle.

- Do not disconnect the airbag connection behind the radio panel.

PRELIMINARY:

Please read the entire mannual before installing this interface.

Vehicle must be equipped with factory DVD changer.

This interface does not activate DVD reader.

IMPORTANT:

ONLY COMPATIBLE WITH:

CIC2 PROFESSIONAL NAV SYSTEMS

INSTALLING THE INTERFACE:

1. Remove the factory radio to access to the factory ber optic cables.

2. Remove the ber-optic cable from the factory connector.

3. Connect the RED wire to 12v and BLACK to ground on the 8-pin

connector from the interface.

4. Make the T-Harness connections behind the factory radio.

(if the connectors do not match please contact tech support)

5. Test and make sure the Reverse gear triggers the interface and

also test the video in-motion while the car is rolling.

(Navigation address input should be active while rolling)

6. Make all other connections before re-installing the factory

radio.

NOTE: To deactivate the Video In-Motion, please connect the BLUE

wire to 12v.

INSTALLATION OVERVIEW

Rev. 052913

Produkt Specifikationer

Mærke:	CRUX
Kategori:	Ikke kategoriseret
Model:	VIMBM-87

Har du brug for hjælp?

Hvis du har brug for hjælp til CRUX VIMBM-87 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CRUX Manualer

CRUX VIMMB-85N Manual

10 Juli 2025

CRUX VIMPR-90P Manual

10 Juli 2025

CRUX VIMCF-93C Manual

10 Marts 2025

CRUX VIMFD-95F Manual

10 Marts 2025

10 Marts 2025

10 Marts 2025

10 Marts 2025

10 Marts 2025

10 Marts 2025

CRUX VIMMB-85P Manual

10 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Microchip ATTINY861 Manual

19 Juli 2025

Husqvarna Aspire P4A 18-C100 Manual

19 Juli 2025

Ikea TJUSIG 201.526.34 Manual

19 Juli 2025

Atlona AT-VGW-250 Manual

19 Juli 2025

Sharkoon MK3 Manual

19 Juli 2025

Yamaha WaveRunner FX SVHO (2025) Manual

19 Juli 2025

Fuxtec FX-GS36S Manual

19 Juli 2025

Bartscher 3L-1 Manual

19 Juli 2025

Guede GF 3060.1 Manual

19 Juli 2025

ChamSys GeNetix GD10 Manual

19 Juli 2025