CyberData Systems 011324 Manual

CyberData Systems Modtager 011324

Læs gratis den danske manual til CyberData Systems 011324 (3 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om CyberData Systems 011324, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Quick Start Guide 931155B

The IP Endpoint Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operations Guide,

which is available in the Downloads tab at the following webpage:

https://www.cyberdata.net/products/011324/

Note You can also navigate to the Downloads tab by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

IEEE 802.3af or 802.3at PoE Switch IEEE 802.3af or 802.3at PoE Injector

Set PoE power type to Class 0 = 15.4W

for high power PoE+ set Class 4 = 30W

CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

SIP

OUR PRODUCTS

VOIP PRODUCTS

011324 SIP PAGING AMPLIFIER Downloads

SIP Paging Amplifier

Quick Start Guide

Quick Start Guide 931155B

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device during the initialization process. See the following figure:

3.2. The Power (Pwr) LED is GREEN for 802.3af and is BLUE for 802.3at. The

GREEN Status LED and the GREEN Power (Pwr) LED come on

immediately. The Speed (SPD) LED illuminates AMBER for a 100Mb link or

is off for 10MB when the network link to the device is established. The Link/

Activity LED blinks to indicate network traffic.

After about 20 seconds, the GREEN Status LED will blink fast to indicate

that the device is acquiring an IP address and attempting to autoprovision.

It will turn off thereafter until the device has finished booting. When the

device has fully booted, the GREEN Status LED will turn on solid.

If there is no DHCP server available on the network, it will try 12 times for 60

seconds and eventually fall back to the programmed static IP address (by

default 10.10.10.10) or the previously used DHCP address if a prior lease

was established. This process will take approximately 80 seconds.

3.3. When the device has completed the initialization process, press and hold

the RTFM switch for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

SPD

PWR

Link/Act

Status

Volume

Power (Pwr) LED

( )BLUE/GREEN

Speed (SPD) LED

(AMBER) (100Mb)

Link/Activity (Link/Act.) LED

( )GREEN

Status LED

( )GREEN

Produkt Specifikationer

Mærke:	CyberData Systems
Kategori:	Modtager
Model:	011324

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberData Systems 011324 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager CyberData Systems Manualer

CyberData Systems 011407 Manual

31 August 2024

CyberData Systems 011324 Manual

27 August 2024

CyberData Systems 011404 Manual

27 August 2024

CyberData Systems 011405 Manual

27 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Rane Zone Power Eight Manual

14 Juni 2025

Blaupunkt Melbourne 130 Manual

14 Juni 2025

NVX NDA12001 Manual

14 Juni 2025

Denon AVC-1930 Manual

14 Juni 2025

Blaupunkt Kansas City 910 Manual

13 Juni 2025

Planet Audio PL3000.2 Manual

13 Juni 2025

AEA 1029 Manual

13 Juni 2025

Planet Audio AC1000.2 Manual

13 Juni 2025

Blaupunkt Osaka 110 Manual

13 Juni 2025

Blaupunkt Kansas City 920 Manual

13 Juni 2025