DataComm 45-0022-WH Manual

DataComm Ikke kategoriseret 45-0022-WH

Læs gratis den danske manual til DataComm 45-0022-WH (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om DataComm 45-0022-WH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Parts Included:

1. 45-0021-WH Recessed Low Voltage Cable Plate

with Recessed Power

2. Recessed Low Voltage Cable Plate with Recessed

Locking Inlet

3. 6 Ft. 14/2 with Ground Extension Cord

Use the Recessed Low Voltage Cable Plate with Recessed

Locking Inlet to install power and low voltage cables behind your

flat panel TV, amplifier or other audio and video devices to your

equipment room or at the location of your head end equipment.

IMPORTANT INSTRUCTIONS:

 Use the local electrical code approved installation when

installing this product.

 The electrical parts in this kit are designed to be used

only as a kit and none of these electrical parts are

designed to be used individually.

 This product is not designed to be part of your home or a

commercial building’s electrical wiring system.

 This installation is only energized (electrically active)

when the supplied 6 ft. cord is plugged into the recessed

locking inlet located on the recessed low voltage cable

plate and the locking end of the 6 ft. cord is plugged into

either your surge protector or wall receptacle.

 If you are not familiar with home wiring systems, please

call a qualified electrician to install this product.

Installation Instructions for New Construction:

Simply use a new nail on box and follow all other instructions

described in the retrofit portion of the instruction sheet.

Installation Instructions for Retrofit Only:

1. Select the location of your flat panel TV mounting

bracket. Now select the location for both the 45-0021-

WH Recessed Low Voltage Cable Plate with Recessed

Power and the Recessed Low Voltage Cable Plate with

Recessed Locking Inlet.

2. Both the Recessed Low Voltage Cable Plate with

Recessed Power and the Recessed Low Voltage Cable

Plate with Recessed Locking Inlet are designed to be

mounted between two studs (see Figure 1). Using the

template supplied (see back of instruction sheet), trace

the openings needed for both recessed cable plates.

Using a drywall knife cut a hole in the drywall the size of

the template.

3. Remember that the Pro-Power kit is not part of your

home’s electrical wiring system. Before installing the

single gang retrofit workboxes (see Figure 2), pull a

piece of 12/2 or 14/2 with ground UL approved building

wire from one opening to the other opening to connect

the recessed cable plate with recessed power to the

recessed cable plate with recessed locking inlet. Make

sure the piece of wire is long enough to allow for easy

installation of the receptacles. Insert a single gang

retrofit workbox (see Figure 2). Securely fasten the

workbox to the wall.

DataComm Electronics, Inc.

6349 Peachtree Street

Norcross, GA 30071-1725

888.223.7977

770.662.8205

www.datacommelectronics.com

Instruction / Installation Sheet

DataComm Electronics 45-0022-WH Recessed Pro-Power Kit with Locking Inlet

Figure 3 Figure 4

Figure 1 – Front View

Figure 2 – Back View

3/22/10 Rev. 8

4-11/16”

Installation Instructions 45-0022-WH (continued):

4. To connect the receptacle on the Recessed Cable Plate with

Recessed Power to the piece of 12/2 or 14/2 with ground UL

approved building wire that you pulled from one opening in the

drywall to the second opening in the drywall, strip off

approximately 3 inches of the outer jacket of the UL approved

building wire. Be careful not to cut the jacket of the inner wires.

Connect the hot line (black) wire to the brass colored terminal

screw and neutral (white) wire to the silver colored terminal

screw. Be sure to connect the bare grounding wire to the green

colored terminal screw (see Figure 3).

5. Once you have wired the Recessed Cable Plate with Recessed

Power receptacle, begin by inserting the receptacle portion of

the plate into the retrofit work box. Once the entire recessed

plate is flush to the wall, using the two white screws supplied,

screw the receptacle portion of the plate to the work box. Next,

screw down the screws with wings. The wings will fasten tightly

against the back of the drywall. Plug all necessary video and

audio cables through the opening on the Recessed Cable Plate

with Recessed Power and down the wall to the opening you cut

out for the Recessed Cable Plate with Recessed Locking Inlet.

6. To connect the Recessed Cable Plate with Locking Inlet to the

UL approved 12/2 or 14/2 building wire with ground, fully back

out the brass and silver terminal clamps. Insert building wire

conductors into the proper wire well. Insert the hot line (black)

wire into the wire well with the brass screw, insert the neutral line

(white) wire into the wire well with the silver screw. Once the

building wire is inserted into the proper wire well, tighten terminal

screws firmly to 10-12 in.-lbs. Then connect the grounding solid

copper wire to the green grounding screw located on the end of

the locking inlet (see Figure 4). Make sure the solid copper

grounding wire is securely fastened onto the green grounding

screw and properly grounded. Plug all necessary video and

audio cables through the opening on the Recessed Cable Plate

with Locking Inlet. Insert the locking inlet portion of the plate into

the retrofit work box. Once the entire recessed plate is flush to

the wall, using the two white screws supplied, screw the locking

inlet portion of the plate to the work box. Next, screw down the

screws with wings. The wings will fasten tightly against the back

of the drywall. Make sure to keep your UL approved building

wire away from the video and audio cables (see Figure 2).

7. Install your flat panel TV mounting bracket per the flat panel TV

bracket manufacturer’s instructions. Make sure to read all

instructions.

8. Now plug your flat panel TV or TV/Projector into the Recessed

Cable Plate with Recessed Power (see Figure 1). Then plug

the female end of the supplied 6 ft. cord into the Recessed

Cable Plate with Recessed Locking Inlet (see Figure 2) and

male end into either your surge protector or wall receptacle.

9. For shock protection, both the UR, UL recognized receptacle

and inlet components must be properly grounded.

10. Caution – use copper wire only with this receptacle and inlet.

WARNING

 DataComm Electronics’ products shall be installed and

used only as indicated in DataComm Electronics’ product

instruction sheets.

 Instruction sheets are available online at

www.datacommelectronics.com.

CAUTION

 For shock protection, this device must be properly

grounded.

 Use copper wire only with this device.

IMPORTANT INSTRUCTIONS

 Read and understand all instructions.

 Follow all warnings and instructions marked on the product.

 Do not use this product near water, for example near a bath

tub, wash bowl, kitchen sink, laundry tub, in a wet

basement, or near a swimming pool.

 SAVE THESE INSTRUCTIONS.

3/22/10 Rev. 8

ONLY LICENSED PROFESSIONALS SHOULD INSTALL THIS PRODUCT

This product is patent protected by U.S. Patent numbers D553475, D554475 and 7390964.

Multiple patents pending. RoHS Compliant.

TEMPLATE

45-0021-WH Recessed Cable Plate

with Recessed Power

45-0022-WH Recessed Low Voltage

Cable Plate with Recessed Locking

Inlet

CTUAL SIZE

CUT ALONG DOTTED LINE 

3-3/4”

Produkt Specifikationer

Mærke:	DataComm
Kategori:	Ikke kategoriseret
Model:	45-0022-WH
Produktfarve:	Hvid
Certificering:	RoHS
Sokler, antal:	1

Har du brug for hjælp?

Hvis du har brug for hjælp til DataComm 45-0022-WH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret DataComm Manualer

DataComm 45-8021-1S Manual

31 Juli 2025

DataComm 50-6653-WH-KIT Manual

30 Juni 2025

DataComm 45-0022-WH Manual

14 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025