Datalogic QuickScan Manual

Datalogic Stregkodelæser QuickScan

Læs gratis den danske manual til Datalogic QuickScan (16 sider) i kategorien Stregkodelæser. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Datalogic QuickScan, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Electronic Article Surveillance (EAS)

Installation Instruction Manual

Introduction

The EAS option enables nners toQuickScan QS6000 Plus model sca

provide Electronic Article Surveillance (EAS) deactivation.

This document provides information and procedures to install a new

EAS Antenna Upgrade Kit, or to replace a malfunctioning loop antenna

already installed in the canner. s

The EAS upgrade or replacement of the loop antenna in the scanner

involves:

• Replacing the Scan Window with a new thinner Scan Window

and the EAS Loop Antenna;

• Replacing the Handle Printed Circuit Board (PCB) with one that

contains a connector for the EAS Antenna leads, and

• Replacing the Interface Cable with a special EAS Interface Cable.

The loop antenna connects to the store’s EAS System through this special

Interface Cable

Before installing the upgrade or replacing the EAS antenna, verify that

your EAS Upgrade Kit contains the following items shown in Figure 1.

Scan Window

Loop Antenna

To EAS System

EAS/Interface

Cable

Figure 1. EAS Kit

1. Scan Window/

EAS Antenna.

2. Handle PCB.

3. Insulation Tape Strip

4 . This Instruction Sheet

You should also have the correct

EAS/Interface cable that matches

your POS Terminal connection.

QuickScan® QS6000 Plus

Tools Required

You need the following tools to upgrade or replace the EAS

Antenna:

• Torque Limiting Driver.

• T8 Torx® bit.

• Multimeter (or equivalent) to test for continuity.

• ESD (ElectroStatic Discharge) protection as described below.

• .050 hex driver

ElectroStatic Discharge Protection

To protect static sensitive circuitry, follow these ElectroStatic Discharge

(ESD) procedures when upgrading, or servicing an existing EAS antenna.

Figure 2 shows the ESD materials.

Figure 2. ESD Setup

ESD Procedures:

1. Connect the above ESD components together with a common

ground strap to eliminate any electrical potential.

2. Use the anti-static floor and table mats to neutralize the working

area (floors, carpeting, tables, etc.).

3. Use the anti-static wrist strap to eliminate buildup static charge

picked up from the environment (shoes on carpets, etc.).

4. Attach the anti-static ground clip to a known ground point.

PSC and the PSC logo are registered Trademarks of PSC INC.

QS6000/6000 PLUS

a trademark owned by PSC, Inc. Torx® is a registered trademark of Camcar Textron.

ESD Materials:

1. Anti-static tablemat

2. Anti-static wriststrap

3. Anti-static floormat

4. Earth Ground

Alerts you to use

ESD protection.

Torx® is a registered trademark of Camcar Textron.

Produkt Specifikationer

Mærke:	Datalogic
Kategori:	Stregkodelæser
Model:	QuickScan
Kode for international beskyttelse (IP):	IP42
Type:	Håndholdt stregkodelæser
Bredde:	28 mm
Dybde:	26 mm
Højde:	67 mm
Vægt:	121.9 g
Batteriteknologi:	Lithium-Ion (Li-Ion)
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Driftstemperatur (T-T):	0 - 50 °C
Kabler inkluderet:	USB
Forbindelsesteknologi:	Trådløs
Certificering:	IEC 60825-1
LED-indikatorer:	Ja
Strømkilde type:	Batteri
Bæredygtighedscertifikater:	RoHS
Indgangsspænding:	5 V
Trådløs rækkevidde:	12 m
Standard grænseflader:	USB
Bølgelængde:	610 nm
Lydalarm:	Ja
Tilt læsningsvinkel:	-45 - 45 °
Pitch læsningsvinkel:	-65 - 65 °
Yaw læsningsvinkel:	-65 - 65 °
Understøtter matrix (2D) stregkoder:	Ikke understøttet