DPW Design 4-Band Dist Manual

DPW Design Ikke kategoriseret 4-Band Dist

Læs gratis den danske manual til DPW Design 4-Band Dist (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 23 anmeldelser. Har du et spørgsmål om DPW Design 4-Band Dist, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

4-Band Distortion Mög D-2

Pre-amp, overdrive and distortion

The D-2 is a four band pre-amp, overdrive and distortion module in Eurorack format with manual or CV

control over the on and off.

You should see the D-2 as a four band vintage type equalizer that can be set to be as clean or

overdriven/distorted as you like. It is designed to be very dynamically playable.

Each frequency band has its own gain so it can be set to work as everything from a fairly clean boost,

overdrive or distortion. Each band can also be completely turned off.

It is a pure analog module built on JFET technology to get a sound similar to a tube amp design, or like 4

parallel tube amps. Only transistors, capacitors and resistors in the distortion part of the module. No clipping

OP-Amps or diodes. Old school design.

The benefits of the multi band approach is that you don't get a sound that just clogges up the lower mid

range when you turn up the distortion. You can still control the low end and not lose the fat bottom of your

sound. You could also decide to let through some of the high end relatively unaffected to still have the

snappy transients that heavy distortion otherwise would compress away.

It has a CV or manual controllable on/off that is eqipped with a super fast switch and an evaluating circuit

that waits until it can do a glitch free switch. This means that it waits from instantaious switching to max

50ms, sometime during that time it will be the perfect time to switch.

This built in evaluating circuit switch control opens up for some unique types of sounds when controlled at

audio rate.

Controls

Erurorack level input.

If the Gain LED lights up with just something connected to In, don't bother. It

can take 10V signals without internal clipping in the wrong part of the

module. The use of the Gain LED is described under Hi-Z.

In and Hi-Z are mixed in the module and can be used at the same time.

Hi-Z

High impedance input for guitar, bass and other low level signals.

Can also be used to bring line level signals like normal synths to eurorack

level.

To check the aproptiate level of a line device in to Hi-Z. Set the Gain knob to

max. If the Gain LED lights up turn down the outupt of your line level device

till the LED isn't lit. This is to check that you don't get distortion in the Hi-Z

pre-amp and theirby loose the benefits of having a multiband distortion.

The Hi-Z input behaves like a tube pre-amp and will color the sound a bit if

you drive it hard. This means that a bit of compression will happen here.

So if you connect a guitar then the sound will be nice and useful even in

clean bypass mode as you get some compression of the transients and that

way the sound will appear natural.

Gain

The overall gain in to the multiband distortion section.

You can set the balance of the distorted bands and just set how hard you

drive all of them with the Gain knob.

DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden

www.dpw.se MAN-D-2 Rev A

Vol

The overall volume out from the multiband distortion section. The Vol LED lights up when you set the volume

to more than 6V. Nothing bad happens when it is lit, it is just a visual indication and a mixing help.

Low

This band is made to be able to let the really low frequencys through without too much distortion if you like to

keep the bottom end.

LoMid

This band has the most gain. This is where the growl is. Turn it up till you have right amount of low mid dirt.

HiMid

This band is there for coloration of the higher mid band if you like.

High

The center frequency of this band has been selected to specifically let through the metallic string sound of a

bass and the high frequency content of transients. It is designed to be high enough to give your sound some

vivid life but also cuts the really high frequencys a bit so it doesn't sound harsh.

If you play bass through the module and it doesn't cut through the mix turning this up could do the trick.

There are a switch and a CV input for turning the distortion on. The switch takes presence over the CV in.

The module will always switch on in a glitch free way as described in the introduction.

Anything above 1V on the CV On input will turn the module on. From DC to high audio rate.

Out

Eurorack level out.

Block diagram

Device specs

Module size: 10 hp wide, 29 mm deep with power connector.

Input impedance: 100 kohm on In and 3 Mohm on High-Z.

Out impedance: 1 kohm

Power requirements: +12V. Max power consumption 25 mA

-12V. Max power consumption 15 mA

Connect the power cable with the red stripe towards the marking -12V on the board.

The unit is protected for reverse power.

DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden

www.dpw.se MAN-D-2 Rev A

Produkt Specifikationer

Mærke:	DPW Design
Kategori:	Ikke kategoriseret
Model:	4-Band Dist

Har du brug for hjælp?

Hvis du har brug for hjælp til DPW Design 4-Band Dist stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret DPW Design Manualer

DPW Design Zero 2 Manual

24 August 2024

DPW Design Shape Manual

24 August 2024

DPW Design Switch Manual

24 August 2024

DPW Design Limit Manual

24 August 2024

DPW Design AV2 Manual

24 August 2024

DPW Design 4-Band Dist Manual

24 August 2024

DPW Design Wavefolder Manual

24 August 2024

DPW Design Mix Manual

24 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025