DPW Design Wavefolder Manual

DPW Design Ikke kategoriseret Wavefolder

Læs gratis den danske manual til DPW Design Wavefolder (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om DPW Design Wavefolder, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Wavefolder WF-1 and E-1 Expander

WF-1 is a Eurorack format wavefolder with some extra functions. It can be used for audio signal manipulation

or as a utility module for control voltages. Everything in the module is DC coupled.

It is mainly made up of two wavefolders. One for the positive side of the incoming wave folding it down and

one for the negative side of the wave folding it up. The two folders can be operated individually or connected

so you can fold asymmetrically or symmetrically.

Getting started

The artwork on the panel is done to explain the signal

paths in the module. White background of jacks

indicate outputs.

White lines represent clean signal.

Yellow lines represent the modulation and control path.

Red lines represent output signals.

The position of knobs and switches on the picture is a

good starting position.

In this position an audio signal in on IN will pass

unaffected to the OUT jack.

From this setting you can start turning OffP and OffN

towards its center position to activate the folders.

For audio OffP and OffN is mainly useful from center

position to fully clockwise.

You can see when the folder is starting to affect the

signal as the FoP and FoN LEDs starts flashing.

Turning the FoP away from the center position will add

or subtract a square wave to the OUT jack. FoP and

FoN are normaled to OUT via the main volume out,

orange knob.

You can see how much is being sent out from FoP and

FoN by the LED along the outgoing red lines.

Controls, in and outputs

Audio or control voltages in. Whatever you want to affect with the module. The complete signal path through

the module is DC coupled.

Clean

Sets the amount of clean signal going to the main mix in the OUT jack.

OUT

The main mix output. The output volume is controlled via the orange out volume knob.

The signals FoP and FoN are normaled to the OUT jack via the out volume knob.

Both the folder part of the module, FoP and FoN can output +/-5V. So if all of them are full on the out volume

knob will have to be rolled down if you don't want the output to exceed +/-5V.

DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden

www.dpw.se MAN-WF-1 Rev B

OffP

Offset for the positive folder. This is the threshold value for the positive folder. It can be set from -8V to +8V.

For audio signals OffP is mainly usable from its center position to fully clockwise. That is from 0 to +8V.

Setting the offset to negative voltages can be useful for manipulating control voltages.

Control voltage in to the attenuverter P controlling the positive wavefolders offset voltage.

This signal is added to the OffP level.

The LED close to the P knob shows the output voltage from the attenuverter. Green is positive and red is

negative voltage going to the Mod knob that controls the amount of folding.

OffN

Offset for the negative folder. This is the threshold value for the negative folder. It can be set from +8V to -8V.

For audio signals OffP is mainly usable from its center position to fully clockwise. That is from 0 to -8V.

Setting the offset to positive voltages can be useful for manipulating control voltages.

Control voltage in to the attenuverter N controlling the negative wavefolders offset voltage.

This signal is added to the OffN level.

The LED close to the N knob shows the output voltage from the attenuverter. Green is positive and red is

negative voltage going to the Mod knob that controls the amount of folding.

Mod

The amount of signal fed down to the main mix resulting in the folding effect together with the Clean signal.

Mod controls the volume of the folding signal from the sum of the positive and negative folder.

The LED below the Mod knob shows the output voltage going to the main out mix. Green is positive and red

is negative voltage.

Sym

The folding is done individually on the positive and the negative side of the incoming signal when the switch

is down. Asymmetrical mode.

Setting the switch to Sym makes the folders go symmetrically, folding equally from both the positive and

negative side of the incoming signal.

With this setting OffN is disconnected and the offset value for both sides are controlled via OffP.

The attenuverter signals coming from P and N are added together and sent to both the positive and negative

folder.

FoP

Folder Positive. The FoP signal is normally low, -5V. When the positive folder is active the FoP signal goes

high, +5V. You can see this on the LED next to the FoP knob.

The FoP knob is an attenuverter. The output level from this attenuverter can be seen on the LED along the

red lines after the knob. Green for positive and red for negative voltages.

This output is max +/- 5V and can be used as an audio source or a gate signal.

If the FoN LED isn't flashing the folder has stopped in an on or off state and will output a DC voltage. Can be

useful when used with control voltages as a DC offset on the output.

The output of FoP is normaled to OUT via the main out volume control.

FoN

Folder Negative. The FoN signal is normally low, -5V. When the positive folder is active the FoP signal goes

high, +5V. You can see this on the LED next to the FoN knob.

DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden

www.dpw.se MAN-WF-1 Rev B

Produkt Specifikationer

Mærke:	DPW Design
Kategori:	Ikke kategoriseret
Model:	Wavefolder

Har du brug for hjælp?

Hvis du har brug for hjælp til DPW Design Wavefolder stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret DPW Design Manualer

DPW Design Zero 2 Manual

24 August 2024

DPW Design Shape Manual

24 August 2024

DPW Design Switch Manual

24 August 2024

DPW Design Limit Manual

24 August 2024

DPW Design AV2 Manual

24 August 2024

DPW Design 4-Band Dist Manual

24 August 2024

DPW Design Wavefolder Manual

24 August 2024

DPW Design Mix Manual

24 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025