Draper 24703 Manual
Læs nedenfor 📖 manual på dansk for Draper 24703 (4 sider) i kategorien Måling. Denne guide var nyttig for 4 personer og blev bedømt med 4.6 stjerner i gennemsnit af 2.5 brugere
Side 1/4
24703
EN
Original Instructions
Version 1
April 2024
5V & 12V
INJECTOR TESTER
– 2 –
User Manual for: Injector Tester
Stock No: 24703
Part No: ETIT
Read this manual in full before using this product and
retain it for future use. Always use the latest version of
the manual. Please visit for drapertools.com/manuals
the latest version.
1. Intended Use
This injector tester is designed to electronically operates
injectors individually; for fault nding fuel delivery issues
such as blocked, sticky or leaking injectors. Switchable
12V & 5V outputs depending on injector type being
tested/activated and can also be used for injector
cleaning in continuous mode.
Four selectable modes; Short / Medium / Long /
Continuous and three pairs of extension leads included
for restricted engine bays.
Any other application beyond the conditions established
for use will be considered misuse. Draper Tools accepts
no responsibility for improper use of this product.
This product is suitable for use by enthusiasts and
tradespersons alike.
2. Specication
3. Health and Safety Information
Important: Read all the Health and Safety instructions
before attempting to operate, maintain or repair this
product. Failure to follow these instructions may result in
injury or damage to the user, the product or the vehicle.
WARNING!
• Follow the vehicle manufacturer’s instructions, warnings
and service procedures.
• Wear eye protection during use of this tester.
• switch o the engine before using the tester to ALWAYS
prevent any hazards or damage.
• Use in a well ventilated room and avoid breathing in the
exhaust emission and vapour. smoke in the DO NOT
vicinity and keep away from ames.
• DO NOT spill fuel on the hot engine.
• The tester is only suitable for use with electronic fuel
injection (EFI) and gasoline direct injection (GDI) systems.
It is not suitable for diesel or other systems.
• The current required to open the injector valve is not a
xed value and will vary depending on the fuel pressure.
The higher the pressure the higher the current required
to open the valve.
• exceed the maximum current specied for the DO NOT
tester – 12V is 1A and 5V is 2A.
• Only use a 12V DC battery, use 24V or any other DO NOT
voltage with this tester.
• DO NOT short contact either the positive or negative
terminals of the battery.
• DO NOT contact any energised conductors.
• Restore the wire connection after testing.
• DO NOT use this device if the tester or leads are damaged
in any way.
• DO NOT attempt to repair this device; it contains no
user-serviceable parts.
4. Symbols
Stock No. 24703
Part No. ETIT
Power Supply: 12V DC Vehicle battery
Injector Type 1:
12V EFI
(Electronic fuel injection)
Injector Type 2:
5V GDI
(Gasoline direct injection)
Fuel Type: Petrol
Net Weight: 243g
Tester Dimensions (L X W X H): 140 X 90 X 135mm
Positive/Negative Injector
Lead Length:
450mm
Positive/Negative Battery
Lead Length:
450mm
Positive/Negative Extension
Lead Length:
3 x 140mm
Read the instruction manual
WEEE – Waste Electrical & Electronic Equipment
Do not dispose of Waste Electrical & Electronic Equipment
in with domestic rubbish.
Produkt Specifikationer
| Mærke: | Draper |
| Kategori: | Måling |
| Model: | 24703 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Draper 24703 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Måling Draper Manualer
7 Juni 2025
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
Måling Manualer
- Måling Soehnle
- Måling Stamos
- Måling Danfoss
- Måling Adwa
- Måling Siglent
- Måling Seaward
- Måling Garmin
- Måling HT Instruments
- Måling Black And Decker
- Måling MSW
- Måling PCE
- Måling Hilti
- Måling Hikmicro
- Måling Park Tool
- Måling Owon
Nyeste Måling Manualer
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025