Draper Star Manual

Draper Projektionslærred Star

Læs gratis den danske manual til Draper Star (1 sider) i kategorien Projektionslærred. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Draper Star, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Crimp

Luma pictured

Operating Instructions—Standard

To lower picture surface, pull screen down. —then allow screen to retract Hesitate

very slowly until it locks in place.

To raise picture surface, pull screen down and, while holding, allow for slow

retraction into the case to reduce risk of injury from falling screen.

Operating Instructions—AutoReturn (Available with Luma)

To lower picture surface, pull screen down. —then allow screen to retract Hesitate

very slowly until it locks in place.

To raise picture surface, pull screen down gently until it stops, then release.

Wall Mounting

(Hardware not Included)

Ceiling Suspended

(Hardware not Included)

T–Bar Twist Clips

(Optional Equipment)

Extension Brackets

(Optional Equipment)

If you encounter any difﬁ culties installing or servicing your screen, call your dealer

or Draper, Inc., Spiceland, Indiana, (765) 987-7999, or fax (765) 987-7142.

Installation/Operating Instructions

Luma and Star Spring Roller Operated Projection Screens by Draper

Installation

Your Draper screen can be mounted on a wall or suspended from the ceiling or

extension brackets. It must be mounted level and with the ﬂ at back parallel to the

wall.

The screen (or extension brackets) should be mounted into studs or blocking in the

wall/ceiling, or in drywall (minimum thickness ½") with speciﬁ ed anchors. For any

other type of installation, follow all local build ing and safety codes.

Steel studs, concrete or cinder block walls and all other types of non-wood frame

construction require the use of special screws or anchors.

The selection of ap pro pri ate mounting hardware should be made by a

qualiﬁ ed professional installer.

Use the upper portion of the holes at the back of the endcap/mounting bracket

for ﬂ ush wall mount ing. Recommended hard ware (not included): For mount ing

into wood or wall stud, use #10 x 1¼" wood screws; for mount ing into dry wall

(minimum ½" thick), use 3/16" tog gle bolts or 3/16" molly bolts. DO NOT USE FLAT

HEAD SCREWS. DO NOT OVERTIGHTEN.

Use the holes at the front of the endcap/

mount ing brack et for sus pend ed mount ing.

Po si tion and prop er ly an chor screw eyes or

oth er fasteners (not included) into ceil ing

joists or oth er sol id sur face. Sus pend “S”

hooks (not included) from fas ten ers (not

included) and hook through holes in the

front of the mount ing brack et. For added

safe ty, crimp both ends of the “S” hooks so

the screen can not come off.

Recommended hardware (not included):

For mount ing into wood or ceil ing joist,

use two

" x 1

" screw eyes and

di am e ter “S” hooks; for mount ing into

dry wall (min i mum

" thick), use

" tog gle

or molly bolts with

" “S” hooks.

Wall mount the brackets (not in clud ed

with screen) using hard ware recom-

mended for “Wall Mounting” (above, not

included). Then, sus pend the screen from

the front holes with “S” hooks. For added

safe ty, crimp both ends of the “S” hooks

so the screen can not come off.

DO NOT OVERTIGHTEN.

➀ Loosen the clip assembly by turn ing the

formed steel hanger counterclockwise.

➁ Spread the clip assembly apart, place over

the T-irons, and ﬁ rmly squeeze the clip

assembly back to geth er, mak ing sure the

clip is ﬁ rmly seated around the T-iron.

Retighten by using pliers to turn the formed

steel hanger clockwise. Make sure it is fully

tightened.

➂ Se cure with the nut. Tighten with pliers.

Please Note: Make sure the clip is

fully tightened around the T-iron, and

that the formed steel hanger and the

lock nut are fully tightened. Poorly

tightened clip assemblies, hangers

or nuts allow the T-Bar Twist Clip to

work loose.

➃ Test by trying to pull the twist clip open and by pulling down on the hanger.

The clip should not pull open.

➄ Suspend “S” hooks (not included) from the holes in the clips and hook

through holes in the front of the screen mounting brack et. For added safe ty,

crimp both ends of the “S” hooks so the screen can not come off.

Please Note: T–Bar Twist Clips are not rec om mend ed for screens larg er

than 70" x 70" unless T-irons are reinforced.

Crimp

Caution

➀ Read and understand these instructions; keep them for future reference.

Follow instructions carefully.

➁ Care in both mounting and correct operation will mean long and satis-

factory service from your Draper screen.

➂ Locate the screen where the audience can best see it, and where other

room fur nish ings permit.

➃ Mount the screen so that the bottom of the picture, when screen is fully

extended, will be above the heads of viewers.

➄ When raising screen, pull down and, while holding, allow for slow

retraction into the case to reduce risk of injury from falling screen.

➅ Screen should be installed level (using a carpenter’s level).

➆ Nothing should be fastened to screen dowel or viewing surface.

NOTE: Screen has been thoroughly inspected and tested at factory and found to

be operating prior to shipment.

Luma

Star

Luma pictured

Clip

Assembly

Screen

Hanger

Nut

Crimp

Luma pictured

Viewing Surface Care & Maintenance

Matt White & High Contrast Grey

Clean surface with a solution of mild dishwashing liquid diluted with warm

water. Sponge the surface, rinse with clear water and blot dry. Do not use clean ing

solvents or abrasives.

Glass Beaded

Clean with a very soft brush or cloth and care ful ly dust the surface. DO NOT

USE SOAP, WATER, SOLVENTS OR ABRASIVES. These substances will damage

a glass beaded viewing surface.

Caution: If mounting screen on old-

style metal wall brackets, do not mount

back of screen to front of bracket.

Lip to prevent screen from

“jumping” off mounting screw

Please note: When installing wall brackets, ﬂ exible driver bit extensions may make

it easier to accurately drive the fasteners into the mounting surface.

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionslærred
Model:	Star

Har du brug for hjælp?

Hvis du har brug for hjælp til Draper Star stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Projektionslærred Draper Manualer

Draper Clarion Manual

22 September 2024

Draper Luma 207008 Manual

6 September 2024

Draper DR230109 Manual

4 September 2024

Draper Luma 207009 Manual

9 August 2024

Draper Traveller 230107 Manual

1 August 2024

Draper Silhouette/Series M Manual

31 Juli 2024

Draper Luma Manual

30 Juli 2024

Draper Premier XL Manual

30 Juli 2024

Draper Consul Manual

28 Juli 2024

Draper DR230107 Manual

28 Juli 2024

Projektionslærred Manualer

Nyeste Projektionslærred Manualer

EPV PMT110HT3-ISF Manual

3 April 2025

EPV EF125C-A4K Manual

3 April 2025

ORAY DRAGONFLY 101 x 180 Manual

2 April 2025

Da-Lite Cinema Vision Manual

1 Oktober 2024

Da-Lite Perm-Wall 78676 Manual

26 September 2024

Pyle PRJSM1006 Manual

19 September 2024

EPV PGF106WH1-A4K Manual

5 September 2024

EPV PGF84WH1 Manual

5 September 2024

KHOMO GEAR GER-1252 Manual

4 September 2024

KHOMO GEAR GER-1273 Manual

4 September 2024