KHOMO GEAR GER-1273 Manual

KHOMO GEAR Projektionslærred GER-1273

Læs gratis den danske manual til KHOMO GEAR GER-1273 (2 sider) i kategorien Projektionslærred. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 12 anmeldelser. Har du et spørgsmål om KHOMO GEAR GER-1273, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
To ensure the performance of your screen, please note the following points:
1. When installing the screen, find a floor or counter top of the correct size. It's best to cover it with a clean
cloth sheet or another soft material so the screen does not get damaged.
2. Do not write or mark the screen or the frame.
3. Do not use sharp or hard objects on the screento avoid scratches or damage.
4.Avoid touching the white part of the screenwith your hands.
5. Do not use a corrosivedetergent to clean the screen. For cleaning use a soft clean cloth to remove dust.
6. During installation, please take it lightly and keep children away.
7. For this assembly it's recommended to have two people involved
Parts Included:
Side Frame x2
Top & Bottom Frame x4
Center Support Bar x2
Long & Short Fiberglass Rod x4
Screen x1
Corner Joint
Plate x4
Spring Hook
x1
Springs
x100
Hanging Bracket
x4
Joint Plates Screws
x24
Wall Anchors
x8
Wall Screws
x8
Center Joint
Plate x2
1. Place the frames facing down onto the floor or (as the image ), and screw the center
plates into place by using the plate screws.
2. After assembling the top and bottom frames, securely fasten the side frame with
corner plates using the designated screws to ensure a stable structure.
4. Place the screen with the white side facing down on top of the facing down frame to
hook the springs. Start by placing the spring in the middle part of the screen (3-4 on
each side ), pulling them toward the frame.
5. Continue to hook the corner springs toward the frame, then complete the remaining
springs until the screen is completely stretched out.
7. Measure the area where the projector screen is going to be hung. Install the brackets
at the least 50-inch apart, and make sure there are aligned. Use a power drill to make
the holes. Insert the anchors then place the brackets and screws into place. 8. Hang your projector screen and Enjoy!
3. For this step we recommend washing your hands, avoid touching the white side of the
screen, and use a clean cloth sheet underneath. Roll out the projector screen with the
black side facing up, and slide the fiberglass rods into the four side pockets of the
screen.
Instructional Video
6. Start by positioning the support bars into the top groove on the back of the frame.
Then, working together, gently extend the bottom frame outward while ensuring the
support bar is centered before securing it into place.
Top
Bottom

Produkt Specifikationer

Mærke: KHOMO GEAR
Kategori: Projektionslærred
Model: GER-1273

Har du brug for hjælp?

Hvis du har brug for hjælp til KHOMO GEAR GER-1273 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Projektionslærred KHOMO GEAR Manualer

KHOMO GEAR

KHOMO GEAR GER-1252 Manual

4 September 2024
KHOMO GEAR

KHOMO GEAR GER-1273 Manual

4 September 2024

Projektionslærred Manualer

Nyeste Projektionslærred Manualer

EPV

EPV PMT110HT3-ISF Manual

3 April 2025
EPV

EPV EF125C-A4K Manual

3 April 2025
ORAY

ORAY DRAGONFLY 101 x 180 Manual

2 April 2025
Da-Lite

Da-Lite Cinema Vision Manual

1 Oktober 2024
Da-Lite

Da-Lite Perm-Wall 78676 Manual

26 September 2024
Draper

Draper Clarion Manual

22 September 2024
Pyle

Pyle PRJSM1006 Manual

19 September 2024
Draper

Draper Luma 207008 Manual

6 September 2024
EPV

EPV PGF106WH1-A4K Manual

5 September 2024
EPV

EPV PGF84WH1 Manual

5 September 2024