Draper Clarion Manual

Draper Projektionslærred Clarion

Læs gratis den danske manual til Draper Clarion (2 sider) i kategorien Projektionslærred. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Draper Clarion, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Assembly/Mounting Instructions

Clarion Permanently Tensioned Projection Screen by Draper

Caution

① Read instructions through completely before proceeding.

② Follow instructions carefully. Installation con trary to instructions

invalidates warranty.

③ When lifting assembled screen, do not lift at only one corner; lift at

both corners. Lifting by one corner could result in damage to the

screen frame, especially on large screens.

④ Screen should be accessible for complete removal should fabric become

damaged or should other ser vice be required.

⑤ Screen should be installed level (using a carpenter’s level).

⑥ Nothing should be fastened to screen frame or viewing surface.

⑦ Make sure you have received all parts (see parts list below and exploded

diagram on page 2).

⑧ Screwdriver required for screen assembly; drill and screwdriver needed

for attachment to wall.

⑨ The ideal temperature range for assembling folding screens to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

If you encounter any difﬁ culties installing or ser vic ing your Clarion screen, call your

dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999; or fax (765) 987-7142.

Clarion—Hardware and Parts List

Frame Preparation

① Clean area and place frame assembly pieces face down. Snap plastic

corner pieces into ends of aluminum frame extrusions as indicated in

Figures 1 through 4.

Figure 1

② Check to verify that all four (4) plastic corners are seated securely in

aluminum frame extrusion lengths (see Fig. 5). Lock in place using eight (8)

self-tapping screws.

Caution: Do not over-tighten fasteners—over-tightening could caUse

damage to the frame corners.

Figure 2

Frame Extrusions - 4

Frame Corners - 4

Z-Brackets - 2

Viewing Surface - 1

Plastic Tubing - 4

Surface Retention

Extrusions- 4

Front

Back

Self-tapping

Screws-8

Figure 3

Figure 5

Figure 4

(Continued on Page 2)

Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.

Clarion by Draper Page 2 of 2

Figure 8

Mounting Screen to Wall

① Determine height at which screen is to be mounted.

Please Note: Top edge of screen frame will be located ½" above mounting

bracket hole centerline when mounted to wall.

② Mark hole centerline so that both Z-brackets can be mounted parallel and

at equal height.

③ Install Z-brackets so that the outermost edges are safely within the overall

length of the aluminum frame extrusion to allow for minor horizontal screen

adjustments (hardware for mounting Z-brackets to wall is not supplied).

④ Position screen slightly above Z-brackets on wall (see Fig. 10).

Please Note: When lifting screen, do not lift at only one corner; lift at

both corners. Lifting by one corner could result in damage to the screen

frame, especially on large screens.

Surface to Frame Assembly

① Return frame onto clean surface, face down, and drape completed surface

assembly over completed frame proﬁ le with rounded edge of surface

retention extrusion visible.

② Insert any side of surface to notch #1 on corresponding side of frame

extrusion (see Fig. 8).

③ Insert opposite side of surface to notch #1 of frame extrusion.

④ Repeat steps 2-3 with remaining edges of surface.

⑤ Ensure surface retention extrusions are centered lengthwise in tension

slots on all 4 edges of surface.

⑥ If additional tension is desired or required over time, adjust surface one

edge at a time to tension notch #2.

Please Note: It is not necessary to adjust more than one edge at a time to

increase surface tension.

Figure 10

⑤ Lower screen until it engages over Z-brackets. Center screen horizontally

on brackets as necessary.

Please Note: Make sure screen is installed level.

Figure 6

Surface Preparation

① Move frame assembly out of the way, unroll viewing surface and place on

smooth/clean surface. (Orient viewing surface so that folded side of hem is

visible.)

② Insert plastic tubing inside pocket formed by hem on all 4 edges of viewing

surface (see Fig. 6).

③ slide surface retention extrusion (rounded edge visible) along Carefully

hem and onto surface on all four edges of fabric (see Fig. 7).

Caution: Do not allow fabric to snag on the ends of the

extrusions. If the screen fabric is not parallel with the surface

retention extrusion, then it may slit and tear during installation.

Please Note: To make this step easier, pinch the end of the pocket closed

before sliding it into the surface retention extrusion.

Figure 7

④ Surface retention extrusion should extend beyond edge of viewing surface

equally at both ends.

⑤ Verify that all surface retention extrusions are installed with rounded edge

visible and are centered on surface material.

Clarion (Exploded Rear View)

Clarion Frame—

Side Detail*

*Viewing surface is approximately ¼" from wall.

www.draperinc.com (765) 987-799

Viewing

Surface

Retention

Extrusions (4)

Plastic

Tubing (4)

Plastic Tubing

Surface Retention

Extrusion

Back of

Viewing Surface

Back of

Viewing Surface

Wall

Z-brackets

supplied with

screen. Installer is

responsible for

ensuring appropriate

hardware is used.

1¼"

Surface Retention Extrusion

Viewing Surface

Fabric Attachment Extrusions

Please Note: To avoid damage to the frame corners, be sure to support a

minimum of two (2) corners when lifting or transporting screen.

Corner Reinforcement

① If screen is being ﬂ own (suspended) or is over 120" (viewing area) height

or width, install Corner reinforcement Gussets to all four corners (see Fig.

9).

Figure 9

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionslærred
Model:	Clarion

Har du brug for hjælp?

Hvis du har brug for hjælp til Draper Clarion stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Projektionslærred Draper Manualer

Draper Clarion Manual

22 September 2024

Draper Luma 207008 Manual

6 September 2024

Draper DR230109 Manual

4 September 2024

Draper Luma 207009 Manual

9 August 2024

Draper Traveller 230107 Manual

1 August 2024

Draper Silhouette/Series M Manual

31 Juli 2024

Draper Luma Manual

30 Juli 2024

Draper Premier XL Manual

30 Juli 2024

Draper Consul Manual

28 Juli 2024

Draper DR230107 Manual

28 Juli 2024

Projektionslærred Manualer

Nyeste Projektionslærred Manualer

EPV PMT110HT3-ISF Manual

3 April 2025

EPV EF125C-A4K Manual

3 April 2025

ORAY DRAGONFLY 101 x 180 Manual

2 April 2025

Da-Lite Cinema Vision Manual

1 Oktober 2024

Da-Lite Perm-Wall 78676 Manual

26 September 2024

Pyle PRJSM1006 Manual

19 September 2024

EPV PGF106WH1-A4K Manual

5 September 2024

EPV PGF84WH1 Manual

5 September 2024

KHOMO GEAR GER-1252 Manual

4 September 2024

KHOMO GEAR GER-1273 Manual

4 September 2024