Draper Targa Manual

Draper Projektionslærred Targa

Læs gratis den danske manual til Draper Targa (4 sider) i kategorien Projektionslærred. Denne vejledning er vurderet som hjælpsom af 59 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 30 anmeldelser. Har du et spørgsmål om Draper Targa, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Hanging Screen

General:

When locating viewing surface and checking clearance for screen’s operation,

remember surface is centered in case. Handle case carefully to protect its ﬁnish.

Regardless of mounting method, screen should be positively and securely sup-

ported so that vibration or even abusive pulling on the viewing surface will not

cause case to work loose or fall. Installer must insure that fasteners used are of

adequate strength and suitable for the mounting surface chosen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. “S” hooks, chains (or cable)

and turnbuckles should be provided by installer. “S” hooks should go through

the front holes on the endcaps (see drawing on page 3), and both ends of the

“S” hooks should be crimped for additional safety. Chains should be attached to

beams or other structural members. Turnbuckles should be adjusted so screen

hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. Installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required.

Wall Installation with Optional 6" Extension Brackets:

Mount the brackets (not included with screen—see diagram on page 3) using

hardware recommended for “Wall Installation” (above). Then, suspend the

screen from the front holes with “S” hooks (as in “Suspended”). For added

safety, be sure to

crimp both ends

of the “S” hooks so the screen cannot come

off. For a more rigid installation, mount the screen from the back holes to the

front of the bracket by using the screws and nuts provided with the brackets.

Wall or Ceiling Installation with Optional Floating Brackets:

Floating brackets should be located on studs or joists. The bracket then

attaches at any almost any point along the case. For details, see separate

instruction sheet that ships with the Floating Wall Bracket.

Operation

Before operating screen remove tape securing fabric and dowel to roller. If view-

ing surface hangs out of case 8"-9", tape has probably been broken by rough

handling in shipment, allowing surface to “unwrap” one turn about the roller.

Manually wrap fabric back around the roller without turning the roller itself.

110-120V Single Station Control —

3-position up-off-down switch permits op-

eration to be stopped at any point. Factory adjusted limit switches automatically

stop screen when fully down or fully up.

110-120V Multiple Station Control

—Switches are similar in appearance to 110-

120V Single Station Control. Screen stops when switch is released and may be

restarted in either direction. Factory adjusted limit switches stop screen auto-

matically when fully down or fully up.

24V Control —

Three-button up-stop-down switches stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop

screen when fully down or fully up.

Key Operated Switching —

Two kinds of key-operated switches are option-

ally available with this unit.

The key-operated power supply switch controls

power to the screen and switches. When it is “off”, the switches will not operate

screen. Key may be removed from the switch in either “on” or “off” position.

A three-position key switch permits the screen to be operated directly by key. In

this case, the screen’s operator must always have a key.

RS232/Ethernet—

Serial communication and network communication optionally

available.

Plug & Play

—

Provided with handheld IR remote control transmitter and 10'

(3m) cord. No wiring necessary except to connect to RS232. Screen is equipped

with a handheld remote or 3-position operating switch. Three positions (up-

off-down) permit operation to be stopped at any point. Factory adjusted limit

switches automatically stop screen when fully down or fully up.

Electrical Connections

Screen operates on 110-120V, 60 hz., 1.1 amp current draw. Duty cycle: On 28

seconds/Off 4 minutes.

Junction box is located inside left endcap and cover plate is secured to endcap

with two screws which may be removed with a Torx-head or small straight-blade

screwdriver. Junction box contains red, black and white pigtail leads and green

internal ground wire, per wiring diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power supply

should be furnished by installer. Please Note: Screen must be installed in accor-

dance with the requirements of the Local Building Codes, the Canadian Electri-

cal Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC), NFPA

70. An appropriate disconnect device shall be provided as part of the building

installation.

Please Note: Do NOT wire motors in parallel.

All operating switches should be “off” before power is connected.

Plug-in power cord option available with built-in low voltage motor.

For Reconﬁguration/Conversion of Non-detachable Power Cord to

Field Wiring for Models TAR-28, TAR-29 and TAR-30 Only:

Disconnect cord plug from outlet.

Remove junction box cover.

Disconnect wire nuts from black, white and green wires.

Remove power cord and strain relief from screen.

Connect the black motor wire to "hot" supply wire.

Connect white motor wire to "neutral" supply wire.

Connect green/yellow wire to "ground" supply wire.

Replace junction box cover.

Ceiling Trim Kit

Optional - must be speciﬁed

Floating Mounting Bracket

Optional - must be speciﬁed

Ceiling Tile

(By others)

Screen

Case

Back

Trim Kit

Targa Electric Projection Screen

INSTRUCTIONS

INSTALLATION & OPERATION

If you have any difﬁculties installing or servicing your

projection screen, call your dealer or Draper, Inc.

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385

draperinc.com | 765.987.7999 | 800.238.7999

CAUTION

Read instructions through completely before proceeding.

Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

Screen should be accessible for complete removal should fabric become damaged

or should other service be required.

Screen should be installed level . The case must also (using a carpenter’s level)

be installed so that the top of the case is level (front-to-back) to prevent the fabric

from contacting the case housing.

Nothing should be fastened to screen dowel or viewing surface.

Operating switch(es) packed separately in screen carton.

Do not discard with packing material.

Screen operates on 110-120V, 60 hz. current.

Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only.

They do not imply any responsibility on the part of the manufacturer

for improper installation or faulty workmanship at the jobsite.

Recessed Installation:

Recess should permit access for remov-

al of screen if necessary. Screen may be

mounted as in suspended or wall instal-

lation. Optional Ceiling Opening Trim Kit

available; see diagrams at right and on

page 3, and separate instruction sheet

(included with Ceiling Opening Trim Kit).

Please Note: Ceiling Opening Trim Kit

is for use in an acoustical, drop ceiling

only. Not recommended for drywall or

hard ceilings

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionslærred
Model:	Targa

Har du brug for hjælp?

Hvis du har brug for hjælp til Draper Targa stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Projektionslærred Draper Manualer

Draper Clarion Manual

22 September 2024

Draper Luma 207008 Manual

6 September 2024

Draper DR230109 Manual

4 September 2024

Draper Luma 207009 Manual

9 August 2024

Draper Traveller 230107 Manual

1 August 2024

Draper Silhouette/Series M Manual

31 Juli 2024

Draper Luma Manual

30 Juli 2024

Draper Premier XL Manual

30 Juli 2024

Draper Consul Manual

28 Juli 2024

Draper DR230107 Manual

28 Juli 2024

Projektionslærred Manualer

Nyeste Projektionslærred Manualer

EPV PMT110HT3-ISF Manual

3 April 2025

EPV EF125C-A4K Manual

3 April 2025

ORAY DRAGONFLY 101 x 180 Manual

2 April 2025

Da-Lite Cinema Vision Manual

1 Oktober 2024

Da-Lite Perm-Wall 78676 Manual

26 September 2024

Pyle PRJSM1006 Manual

19 September 2024

EPV PGF106WH1-A4K Manual

5 September 2024

EPV PGF84WH1 Manual

5 September 2024

KHOMO GEAR GER-1252 Manual

4 September 2024

KHOMO GEAR GER-1273 Manual

4 September 2024