Drayton Digistat 2290B Manual

Drayton Termostat Digistat 2290B

Læs gratis den danske manual til Drayton Digistat 2290B (4 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Drayton Digistat 2290B, eller vil du spørge andre brugere om produktet?

Side 1/4
Programmable Room
Thermostat
Installation Guide
Model: 2290B
1. Remove th frone t cover by releasing th 2 screwe s a the t
bottom. Mo ting holeun s and electrical connections are
found u erneatnd h the hinged black cover (Fig 1).
Before Installation
If you do not have the knowledge to install the
thermostat safely then you must arrange for a
competent electrician or heating engineer to install it
for you. Wiring must conform to the current IEE
regulations.
Prior to commencing the installation you must ensure
the mains supply is switched off.
Digistat
3r Generationd
(Fig 1)
(Fi 3)g
(Fig 4)
(Fig 6)
(Fig 7)
(Fig 2)
2. Fix back plate directly onto the wall using suitable wal plugs l
and screws or mount over existing wall box (Fig 2).
3. Complete the wiring a ording to the con ction suggestions cc ne
4. Close the black hinged ter nami l cover and rep cla e the front
shown n g i (Fi 3). For Basi bo erc il , Combi bo er an Basic il d
bo er withil e e zon valv ap icationpl s t Digista with y batter or
mains supply are suitable.
For Electric Heat application use
Digistat
with mains
supply only.
cover by locating the tw lao tches at the top the fasten n the
2 screws at the bottom (Fig 4).
(Fig 5)
7. Replace the battery cover (Fig 7).
5. Remove th battery cover by s dine li g the battery cover at the
bottom downwards (Fig 5).
6. Install th 2 Ae A batteries provided (Fi 6).g
control the room temperature.
8. The is Digistat now installed and will automatically start to
Technical Helpline Tel: 0333 6000 622
Website: www.draytoncontrols.co.uk
Email: customer.care@draytoncontrols.co.uk
UserandInstallationGuide06490308001IssD
INSTA ER OPTIONSLL
To make changes to the default Installer Options shown below,
enter th Installee r Options menu b pressing thy e setting tton s bu
for 3 se onc ds. This allows access to the User Menu 01, the
Advance User Setting Mend s u 02, th Installer Setting 03e s , and
Service Interval Setting 04. Uss e th + ane d - ttonbu s to scroll to
Installer Options and press O to select. You can exit the menu by
pressing until you have returned to the home screen. I the n
Installer Options menu (Fig 8), scroll thr gh thou e options using
the + and - ttonbu s and pres ts O o select. Scroll thr gou h the
dierent setting usins g the + and - ttonbu s and pres ts O o select
and save. (Fig 9 shows Option 02 OFF).
(Option 01) Partial Assistant (beep)Sight
When enabled, audible to es indicate when the setpo is n int
more than, less than or equal to the current room te perature m
wh us manually adjusts the setpo tton: en a er int using the + bu
Setpo room te perature int > m - single high to 0.5°C ne per
increase
Setpo temperature int = room - double to e n
Setpo room te perature int < m - single low per tone 0.5°C
decrease
(Option 02) Frost Protection
The Digistat will switch on the heating the te falls if mperature
to and mai tains te perature even when 5°C n a m of 7°C
in OFF mode.
(Option 03) Minimum Setpoint Limit
Change minimum setpoi temperature. After any changes to nt
setpoi limits, all setpoi ts in AUTO, MANUAL, BOOST and nt n
HOOLIDAY modes will be modified to conform accordingly.
(Fig 8) (Fig 9)
(Option 04) Maximum Setpoint Limit
Change changes maximum setpoi temnt perature. After any to
setpoi lim setpoi and nt its, all nts MANUAL, in AUTO, BOOST
HOOLIDAY modes will be modified to conform accordingly.
(Option 05) Optimum Start
Whe the n enabled, this uses current temperature, ambient
next sche setpoi capt the duled nt and data heat gain ured by
device to adjust the thermostat early, setpoint so the ambient
tem req starts.perature is at the uired level when the next event
Delayed Start
Whe current n enabled, this uses current temperature, ambient
event setpoi environment nt characteristics and heating of the
to the delay the implementation of setpoint if ambient
temperature is to it, refore already close the saving energy.
(Option 06) Protection Valve Time
In ronic heating systems some hyd it uired to may be req protect
the it given valve operating by for a time. When enabled, this
main tpu operated tenance feature ensures that each relay ou t is
for at ute least (1) one min each week.
(Option 07) sor lt Sen Fau Function
In central heating the event fault, of a sensor outpu is reduced t
to ng heating ON 30% by turni for 3 minutes, then OFF for 7
minutes.
(Option 08) Application Type
Select the central heating system energy type.
(Option 09) System Capability
Select the flow capability of the heating system.
(Option 13) Settings Installer Lock
When enabled, installers settings can lock the installer menu
until a 3 digit code the code is entered. If is forgotten while
device call the Technical is locked, please Helpline.
(Option 20) Reset (Service Interval settings are NOT reset)
Reset to the Digistat its factory original settings.
Service Interval Options continued on reverse.


Produkt Specifikationer

Mærke: Drayton
Kategori: Termostat
Model: Digistat 2290B

Har du brug for hjælp?

Hvis du har brug for hjælp til Drayton Digistat 2290B stil et spørgsmål nedenfor, og andre brugere vil svare dig




Termostat Drayton Manualer

Drayton

Drayton RTS10 Manual

5 Oktober 2024
Drayton

Drayton RTS2 Manual

16 September 2024
Drayton

Drayton PTS1 Manual

5 September 2024
Drayton

Drayton Easy 2 Manual

5 September 2024

Termostat Manualer

Nyeste Termostat Manualer