Drayton MiTime T710R Manual

Drayton Termostat MiTime T710R

Læs gratis den danske manual til Drayton MiTime T710R (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Drayton MiTime T710R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Step 1: Mounting the Wall-plate

! IMPORTANT:

Installation must only be carried out by a

qualiﬁ ed electrician or heating engineer.

Make sure mains input has a 3 amp fuse.

! CAUTION! Before installation, make sure the

mains supply is switched off!

Option 1: Fitting a new wall-plate

The ideal location is 1.2m above

ﬂ oor level, with reasonable

lighting, good access, no

condensation, no extremes of

temperature and a supporting

surface that fully covers the

back of the unit. Position with

70mm clearance to the right,

25mm above and sufﬁ cient room

to access the securing screws

underneath. Fix, with terminals

at the top, either direct to a ﬂ at

wall using wall plugs and No. 6 x

1” (25mm) woodscrews, or on a

ﬂ ush mounting single conduit box

type UA1 (BS4662) using M3.5 x

14 bolts. Check the 3A fuse, and

switch on the mains.

! DO NOT use a surface mounting box



Battery

Handling

Batteries, rechargeable or

not, should not be disposed

of into ordinary household

waste. Instead, they must be

recycled properly to protect

the environment and cut

down the waste of precious

resources.

Your local waste

management authority can

supply details concerning the

proper disposal of batteries.

In compliance with the EU

Directive 2006/66/EC, the

button cell battery located

on the printed circuit board

inside the product, can be

removed at the end of the

product life, by professional

personnel only.

Option 2: Using an existing

industry standard wall-plate

Loosen the securing screws

on the old programmer and

unplug it. Check that there is

70mm clearance to the right of

the wall-plate and 25mm above

it. Check the wiring diagram for

your product model to compare

terminals and, if necessary,

change the wiring of the wall-

plate to suit. Now plug the MiTime

unit into the wall-plate and tighten

the securing screws.

Check the 3A fuse, and switch on

the mains.

MiTime Programmer Series

RF Packs

Customer Service Tel: 0845 130 5522

Customer Service Fax: 0845 130 0622

Technical Helpline: 0845 130 7722

Website: www.draytoncontrols.co.uk

E-mail: customer.care@invensys.com

@DraytonControls

/DraytonControls

EU Design Regs:- 002180638-1/2/3

Installer Guide 06490194001 Iss G

INSTALLATION Guide

Single Channel: MiTime T710R

Dual Channel: MiTime T720R, T720M

Multi Channel: MiTime T740R, T740M

Step 2: Wiring



Connect the wiring as shown above.

T710R only: Note that the output contacts are voltage-

free, so power needs to be put on to Terminal 1 either

by linking from Terminal L or from a separate supply

with a 3A fuse.

Single Channel:

MiTime T710R

Dual Channel:

MiTime T720R, T720M

Ch1 Ch2 Ch3 Ch4

Multi Channel:

MiTime T740R, T740M

Step 3: Wireless Thermostats - Checking the batteries

Step 4: Signal Strength Step 5: Mounting Options Step 6: Cylinder Sensor (T720M, T740M only)

   

How do I know when to change

the batteries?

When the batteries start to run low a battery icon will

ﬂ ash in the display, to indicate “low battery” during

this time the MiStat will function normally (see ﬁ g. to

right). Please replace batteries with 2 x 1.5V IEC LR6

(AA) Alkaline batteries. When the battery icon alone

is shown in the display, the batteries are completely

exhausted and the MiStat will cease to function

(see below). Re-activate by replacing the batteries.

The MiStat Room & Cylinder thermostats are pre-bound to the MiTime

programmer in the factory so they just need to be positioned in the

best place for wireless communication. To help with this there is a built

in Signal strength indicator, available in the Installer settings menu on

the MiTime programmer, as shown. It is recommended that the signal

strength is Good or Very Good to ensure ongoing communication is

maintained.

The signal strength can also be seen on the MiStat thermostat.

To enter signal strength menu

• Press + & - for approx. 5 secs, then scroll (+/-) to show INST-S,

• press (

) to enter the installer menu,

• Press +/- until 11 WIRELESS is shown,

• press ( ) to enter,

• press +/- to show 13 SIG-LEVEL as shown,

• press ( ) to see the current signal strength.

How to replace the batteries

Remove the battery covers using a coin. Replace the

spent batteries with 2 x 1.5V IEC LR6 (AA) Alkaline

batteries ensuring correct orientation. Replace the

battery covers pressing fully home.

MiStat

MiStat Rear

Battery Covers:

Slide outwards

to remove

Once the best position has been identiﬁ ed, the MiStat

should be ﬁ xed to the wall using the wall bracket as

shown. The cylinder thermostat (T720M, T740M only)

should be mounted close to the cylinder using the

wall bracket.

Wiring

Cylinder Thermostat

Cylinder Thermostat Sensor

Locate the external sensor terminal block on the lower

edge of the MiStat C thermostat, connect a 2-core

cable, cut to the required length to reach the sensor

position. Connect to the sensor in the position shown

and fold wires back through the cable grip & out

through the cable entry, re-assemble the housing.

Clip the spacer provided

onto the sensor housing

The sensor should be installed approximately one

third of the way up the hot water cylinder. With pre-

insulated cylinders, mark the position and size, and

remove just enough insulation to allow the sensor to ﬁ t

against the metal of the cylinder in the recess formed.

The plastic covered spring ﬁ xing cable should be cut

to an un-stretched length of approximately 60-75mm

(2½”-3”) less than the circumference of the cylinder

and the hook and eyelet should be screwed intp the

ends. Stretch the cable round the cylinder, over the

insulation, and position it in the groove across the

front of the sensor housing, Engage the hook and

eyelet.

NB. MiStat can also be positioned using the table

stand included.

Care should be taken to mount the thermostat in a

position which is not subject to direct sunlight or draughts.

Preferably it should be mounted on an inside wall about

1.2m (4ft) above the ﬂ oor in a position where it can

respond to room temperature but away from the direct

inﬂ uence of radiators or other appliances giving off heat.

MiStat

Cable entry

Connect here NTC Sensor

Cable grip

1/3 cylinder height

Cylinder

Insulation

Fixing cable

Sensor

Cylinder

MiTime

MiStat

MiTime

! IMPORTANT:

Always switch off the mains before removing

the MiTime programmer – and never ﬁ t it to a

live wall-plate!

eg. eg.

It has to be placed in a location where it will be able to

control the room temperature.

If POOR is displayed, look for a better location

If NO SIGNAL is displayed, try connecting again with the room unit in

a different position. To exit, press + & - keys for approx. 5 seconds. If

there is no key pressed for 2 minutes, the system will exit the menu.

1.2m

Client Invensys File Name 7378 Drayton Instruction Manual Update 06490194001

Artworker -

Proof Stage

Finished Size 420x297mm

Creative Director Mike Lane Artwork % 100%

Modification Date 22/04/15 10:37AM Bleed 3mm

External

Sensor

Produkt Specifikationer

Mærke:	Drayton
Kategori:	Termostat
Model:	MiTime T710R

Har du brug for hjælp?

Hvis du har brug for hjælp til Drayton MiTime T710R stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Drayton Manualer

Drayton MiTime T740R Manual

26 August 2025

Drayton MiTime T740M Manual

25 August 2025

Drayton LP10RF & DIGISTAT+2RF Manual

25 August 2025

Drayton LP10RF & Digistat+3RF Manual

25 August 2025

Drayton Easy 3 Manual

24 August 2025

Drayton Digistat 2290M Manual

24 August 2025

Drayton MiStat C - C110C Manual

13 Januar 2025

Drayton MiTime T710R Manual

13 Januar 2025

Drayton MiTime T720R Manual

13 Januar 2025

Drayton RTS10 Manual

5 Oktober 2024

Termostat Manualer

Nyeste Termostat Manualer

9 November 2025

9 November 2025

8 November 2025

8 November 2025

Soler & Palau THE 16/4A Manual

8 November 2025

Warmup 7iE Matter Manual

7 November 2025

Vimar 30811.C Manual

31 Oktober 2025

Abus Comfion FUSH80100 Manual

29 Oktober 2025

Delta Dore Tybox 137 Manual

17 Oktober 2025

Delta Dore RF 6600 FP Manual

17 Oktober 2025