Dynaudio DA-BM6A Manual

Dynaudio overvåge DA-BM6A

Læs gratis den danske manual til Dynaudio DA-BM6A (6 sider) i kategorien overvåge. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Dynaudio DA-BM6A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

DA-BM6A

OWNERS MANUAL

Congratulations on your purchase of the Dynaudio Acoustics BM6A monitor system. With the

right care and attention it will give you many years of trouble free audio reproduction. It is

most important, however, that you take a few minutes at this early stage in your BM6A’s life to

read the following paragraphs. They contain essential information to enable you to get the

best from your monitors.

Electrical Safety Warning

This unit is supplied with a 3 wire power cord. Under no circumstances should the

earth wire be disconnected.

To prevent possibility of shock hazard do not expose the unit to moisture

There are no user serviceable parts inside. Do not open cover. Refer servicing to

qualified personnel only

Ensure correct mains voltage and fuse are selected before connection to mains

BM6A Owner’s Manual - Issue 2 Page 2

November 1997

Setting Up

Mai

MaiMains Po

ns Po

ns Pons Power Co

wer Co

wer Cower Connect

nnect

nnectnnectio

ioions

nsns

Mains power is applied via a fused IEC inlet. The unit must be earthed. The voltage selector

switch is used to match the unit to the mains voltage in your territory. The mains fuse must be

the correct value for the voltage selected, 115V requires a T3.15A fuse while 230V requires a

T1.6A fuse. The ‘T’ signifies a slow blow type fuse.

You must ensure that the correct voltage and fuse have been selected before

switching the unit on.

Audio Co

Audio CoAudio Connect

nnect

nnectnnectio

ioions

nsns

Audio input is via a female XLR connector. The input is electronically balanced with +ve on

pin 2, -ve on pin 3 and ground on pin 1. If your signal source is unbalanced it is usual to

connect the unused signal pin (i.e. Pin 3) to ground. This is normally done inside the

connecting cable. For best results use only good quality screened cables and connectors.

Your local dealer will be able to advise you

Positioning

PositioningPositioning

The BM6A is designed primarily as a ‘nearfield’ monitor and would normally be positioned

1-3m from the listener. They can be mounted on stands or on the meter bridge of the console

(providing this is substantial enough). For best results the speakers should be ‘aimed’ at the

listener in both vertical and horizontal planes.

In any situation ensure that there is adequate space for ventilation around the heatsink.

Produkt Specifikationer

Mærke:	Dynaudio
Kategori:	overvåge
Model:	DA-BM6A

Har du brug for hjælp?

Hvis du har brug for hjælp til Dynaudio DA-BM6A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

overvåge Dynaudio Manualer

Dynaudio LYD 48 Manual

12 August 2024

Dynaudio DA-BM6A Manual

11 August 2024

overvåge Manualer

Nyeste overvåge Manualer

BenQ DesignVue PD2730S Manual

8 April 2025

Asus VA279QGS Manual

8 April 2025

Acer EV227Q Manual

8 April 2025

BenQ PD3226G Manual

7 April 2025

Philips 221V8LB Manual

4 April 2025

Extron TLS 1025M Manual

2 April 2025

PureTools PT-SCREEN-100 Manual

1 April 2025

Viewsonic VG2752-2K Manual

30 Marts 2025

Satco S13165 Manual

30 Marts 2025

Satco S16434 Manual

30 Marts 2025