Edifier X3 Lite Manual


Læs gratis den danske manual til Edifier X3 Lite (7 sider) i kategorien Øretelefon. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Edifier X3 Lite, eller vil du spørge andre brugere om produktet?

Side 1/7
EN 1. Power ON/OFF
2. Pairing
White LED lit for 1s
1. Power ON when taken out of the case.
2. Power OFF when placed in the case.
Note:
If there is no Bluetooth connection for 10 minutes after powered on, the
earbuds will power o automatically.
For subsequent use, the earbuds will automatically connect to the device
used last time.
1. Taken out of the case. White and red LEDs will blink alternately.
2. Select "EDIFIER X3 Lite" in Bluetooth device setting to connect.
White LED will blink twice in 5 seconds when successfully.
1st Pairing
3. Reset
1. Taken out of the cas
2. Press and hold the touch Disconnected from any Bluetooth device.
panel on either earbud for around 8s until red LED blinks 6 times to
clear the Bluetooth pairing records and power o. If the left and right
earbuds are connected, the other side will clear the Bluetooth pairing
record and power o too.
3. Placed back in the case and taken out of the case again.
4. Select "EDIFIER X3 Lite" in Bluetooth device setting to connect.
White LED will blink twice in 5 seconds when successfully.
Indic cator
Indic
cator
5. Charging
Earbuds
1. When hearing a low batte prompt tone, please place
the earbuds in the case for charging.
2. Red LED on earbud is steady lit when charging and
o when fully charged.
Charging Case
Note:
Please do not charge the earbuds when there is sweat or
other liquids inside the charging po, which may damage
the earbuds.
1. Please connect the case to power source with the
included Type-C charging cable for charging.
2. Red LED is steady lit when charging and o when
fully charged.
Input: 5V 200mA (Earbuds)
5V 1A (Charging case)
1. If there is no Bluetooth connnection and TWS connection when earbuds
are powered on, respectively tap the touch panel 5 times on both earbuds
until white LED blinks slowly to enter TWS pairing mode. Once the left
and right earbuds are successfully, white and red LEDs will connected
blink alternately to enter pairing mode.Bluetooth
2. Select "EDIFIER X3 Lite" in Bluetooth device setting to connect.
White LED will blink twice in 5 seconds when successfully.
Indic cator
4. Left & Right connection
8s
8s
x5 x5
6. Controls
Note:
1. Images are for illustrative purposes only and may dier from the
actual product.
2. Download Edier Connect App for more customizable control settings.
Left Touch Panel Right Touch Panel
x2x2
x2x2
x3x3
x2x2
2s2s
2s2s
For more information, please visit our website:
Model: EDF200131
P.O. Box 6264
Hon Kong g
Printed in China
NOTICE:
For the need of technical improvement and system upgrade,
information contained he e subject to chan e from timerein may b g
to time without prior notice.
s.
Pictures and illustrations shown on thi be sli htl s manual may g y
tual
product pr .evails


Produkt Specifikationer

Mærke: Edifier
Kategori: Øretelefon
Model: X3 Lite

Har du brug for hjælp?

Hvis du har brug for hjælp til Edifier X3 Lite stil et spørgsmål nedenfor, og andre brugere vil svare dig




Øretelefon Edifier Manualer

Øretelefon Manualer

Nyeste Øretelefon Manualer